Vizio L42HDTV10A, GV42L HDTV service manual Write Protect WP, Software Command Definitions

Page 61

If RESET is asserted during a program or erase operation, the RY/BY pin remains a "0" (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY to determine whether the reset operation is complete. If RESET is asserted when a program or erase operation is not executing (RY/BY pin is "1"), the reset operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data tRH after the RESET pin returns to VIH. Refer to the AC Characteristics tables for RESET parameters and to Figure 14 for the timing diagram.

WRITE PROTECT (WP)

The write protect function provides a hardware method to protect boot sectors without using VID.

If the system asserts VIL on the WP/ACC pin, the device disables program and erase functions in the two "outermost" 8 Kbyte boot sectors independently of whether those sectors were protected or unprotected using the method described in Sector/Sector Group Protection and Chip Unprotection". The two outermost 8 Kbyte boot sectors are the two sectors containing the lowest addresses in a bottom-boot-configured device, or the two sectors containing the highest addresses in a top-boot-configured device.

If the system asserts VIH on the WP/ACC pin, the device reverts to whether the two outermost 8K Byte boot sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these two sectors depends on whether they were last protected or unprotected using the method described in "Sector/Sector Group Protection and Chip Unprotection".

Note that the WP/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result.

SOFTWARE COMMAND DEFINITIONS :

Device operations are selected by writing specific address and data sequences into the command register. Writing incorrect address and data values or writing them in the improper sequence will reset the device to the read mode. Table 3 defines the valid register command sequences. Note that the Erase Suspend (B0H) and Erase Resume (30H) commands are valid only while the Sector Erase operation is in progress. Either of the two reset command sequences will reset the device (whenapplicable).

All addresses are latched on the falling edge of WE or CE, whichever happens later. All data are latched on rising edge of WE or CE, whichever happens first.

CONFIDENTIAL – DO NOT COPY

Page 7-42

 

File No. SG-0198

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Vizio GV42L Hdtv Table of Contents Vinc Features Optical Characteristics SpecificationPower Supply Weight Physical weight Dimensions Physical dimension Width 1066 mmMounting Precautions SpeakerOperating Precautions Handling Precautions for Protection TV Source On Screen DisplayRGB Mode AV Component Mode Hdmi MODE： Confidential do not Copy Factory preset timings Pin Assignment Hdmi Connect PIN Assignment Type TV RF connector RGB Signal Main Board I/o Connections Theory of Circuit Operation MT8202 Application Video input YPbPr/Scart/D-connectorDecoder Support Formats Digital port2D-Graphic/OSD processor Supporting OSD mirror and upside downMicroprocessor interface I/O ports are configured as follows：Video processor 1.Color Management Dram Usage DDR Sdram V58C2128164SBI5 Application Pin description Power-UpFunctional Description Command Truth TableMode Register Set MRS Precharge Bank Activate Command Precharge Timing During Read Operation Read OperationPrecharge Timing During Write Operation Burst Stop CommandBurst Write Operation MX29LV160BTTC Flash Application Block Diagram Command Definitions Write COMMANDS/COMMAND Sequences READ/RESET Command WM8776 Application Reading Array DataAudio sample rate Slave mode Confidential do not Copy MT8293 Application Active port detection Tmds Digital CoreHdcp Decryption Video Data Conversion and Video OutputTDA8946 Application I2c Interface to Display ControllerBlock diagram Input configuration Output power measurement MT5351 Application Mode selectionGeneral Feature List CGMS/WSS Confidential do not Copy MX29LV320BTTC Flash Application Confidential do not Copy Block Diagram BUS OPERATION--1 BUS OPERATION--2 Write COMMANDS/COMMAND SequencesTable A. MX29LV320AT/B Command Definitions Reset Operation Standby ModeWrite Protect WP Software Command DefinitionsTable B. Write Operation Status Write Operation StatusFig C. Command Write Operation Fig D. Read Timing Waveforms Fig E. Reset Timing Waveform DDR Sdram NT5DS16M16CS-5T Application Block Diagram 16Mb xFunctional Description Pin Configuration 400mil Tsop II x4 / x8 Mode Register Operation Operating Mode Extended Mode Register Definition Extended Mode RegisterActive Truth Table a CommandsWrite ReadAuto Refresh Self RefreshReads OperationsRandom Read Accesses CAS Latencies Burst Length = 2, 4 or Read Command Write Command Data Input Write Data Output Read PC MODE1366X768 60HZ WaveformsCH1 Green # FB27 CH2 Vgavsync L22 CH1 Vgal R193 CH2 Avol R194 CH1 PCL CE70+ PCL CE70 AV&TV Mode AV1/AV2/TV Video Confidential do not Copy CH1 Dacbclk U23 PIN4 CH1 Dacmclk U23 PIN5 Component Mode Component 1/2 CH1YCBCRL2L19 CH2 2A33 U22 PIN11 CH1 AVL CE71+CH2 Auspl R304 Hdmi 1&2 Confidential do not Copy DTV HD Confidential do not Copy CH1 Vovsync DU9 PIN W1 CH1 Vode DU9 PIN W2 CH1 Vopclk DU9 PIN Monitor Display Nothing PC Mode Trouble shootingTV, Composite VIDEO1, 2, S-VIDEO is not Display Correctly COMPONENT1, 2 is not Display Correctly Hdmi is not Display Correctly Trouble of DC-DC Converter Trouble of DDC Reading System Block Diagram Wxga panel Block DiagramConfidential do not Copy Main Board Block Diagram Page Page Page Page Page Page Page
Top Page Image Contents