Toshiba HDD-J35 manual Appendix 6 Instruction Guide for Programming Remote Control

Page 77

APPENDIX 6 INSTRUCTION GUIDE FOR PROGRAMMING REMOTE CONTROL

The remote control can be compatible with various brands of TV by setting their control codes. The TOSHIBA code has initially been set to control TOSHIBA TVs. Refer to the four methods below for programming your remote control and use the one that best suits your setup. (Note: Every change of batteries in the remote control unit will result in a reset to the default Toshiba code of 138)

Due to the great variety of TV systems, some makes and models are not compatible with your recorder’s remote control. If you reach the end of the available codes without finding a code that works with your device, you will need to use your TV system’s remote control to turn it on and off, and control the volume. Even if the code is found, there is a possibility that not all the buttons on your recorder’s remote control will work with your TV. Control codes for regions Europe, USA and China are available on pages 79 to 86.

1.Programming

(a)Refer to the code list for the 3-digit code of the TV brand.

(b)Press the “TV FUNCTION” button to set the remote control operating your TV.

(c)Press and hold the “PROG.” button, then enter the three digits of your TV brand code using the “CHANNEL NUMBER” buttons.

(d)Check response on LED with every digit pressed;

1)LED lights up after the first digit press

2)LED blinks once after the second digit press

3)If the code is available, LED goes off after the third digit press or else the LED will blink twice and goes off, indicating unavailable code. Go back to step (c) if an unavailable code was entered.

(e)Release “PROG.” button to leave the programming mode.

(f)Point the remote control at your TV and use each button listed below to make sure your TV is operated correctly. (Refer to page 14 and 15 for location of buttons on remote control unit)

- STANDBY/ON , INPUT SELECT, MUTE, CHANNEL UP/DOWN, VOLUME UP/DOWN, CHANNEL NUMBER and DIGIT SELECTION buttons.

2.Auto code search (Region)

If none of the codes listed allows you to control your TV, a code search may detect the correct code. This function performs a forward search in the code list by region.

(a)Turn on your TV. Press and hold the “PROG.” button, then press the “TV FUNCTION” button.

(b)LED lights up, indicating that the remote control is now in programming mode. (LED will go off and remote control exits programming mode if the “TV” button is pressed or no further activity is sensed after ten seconds)

(c)Release the “PROG.” and “TV FUNCTION” buttons.

(d)Input the code “994” (for Europe models) or “995” (for US models) or “996” (for China models).

(e)The remote control is now in “Auto code search” mode.

APPENDICES

77

Image 77
Contents Receiving Recording Playback Appendices Introduction Startup GuidanceSafety Measures on Proper Usage Power Cord CautionsMoisture Condensation Diagrams above are strictly for illustration purposes onlyAbout the Hard Disk Drive HDD Disclaimer About CleaningExemptions Table of Contents TV/RADIO Program List Australian DTV Channel TableIntroduction HD 1080i/720p/576p Capability Video Format Auto-SwitchLarge-Capacity Hard Disk Drive HDMI1Front Panel Identification of ControlsSerial Port Rear PanelDigital Audio Coaxial OUT Hdmi OUTDigital Audio Optical OUT Analog Audio L/R OUTRemote Control Remote Control FP Display Operation IndicatorStartup Guidance Connecting to TV Installing the RecorderStep a Connections Do not Plug the Recorder Into the Mains YETStartup Connections to TV Video ConnectionHDD-J35 HDD-J35 Audio/Video cable Supplied Match the colors when connecting Connecting to Cable BOX/SATELLITE BOX/VCR Connecting to DVD PlayerHDD-J35 Connecting to VCR for ArchivingConnecting to Amplifier Step B Preparing Your Remote Control Connecting to Mains SupplyOperating with the remote control Step C Setting UP Your Recorder Page Turning OFF the Recorder Viewing ProgramsStatus Display PIP TTX ReceivingEPG Menu MAP TOP MenuMain Menu InstallationQuick Scan For Australia Only Reset Data Manual SetupDo not click on the Send button at this UpdateFormat Hard Disk Time yet Program List EPG ProgramProgram List Video Setup Audio Setup Password Time Zone EXT Control Video SetupSystem HD Output Format Aspect RatioPassword Audio SetupDigital Output Audio FormatEXT Control Time SetupFAVORITE&LOCK Parental Rate Edit ChannelFAVORITE&LOCK Virtual Keyboard Parental Rate For Australia OnlyProfile Plate SetupPlate Setup FP Display Setup Information PVR Setup Information FP Display SetupPVR Setup Info I-Plate Quick ControlTV/RADIO Program List FAV. Favorite Channel List TTX Teletext Ratio Aspect Ratio Format Video FormatTo change the off-timer To set the off-timerInput Select SleepRecall AudioPage Recording OTR ONE Time Recording Recording MethodsRecording TIME-BASED RecordingEPG Recording Recording Page Playback Library Playback ControlsPlayback Time Line BARChase Play Stop Playback PauseFast FORWARD/FAST Reverse 3 Speeds Skip FORWARD/REVERSEPage Appendices Number Appendix 1 Australian DTV Channel TableCanberra Phenomenon Solution Appendix TroubleshootingSetup Quick ScanRgbhv YP BP R HD Mode RGB YP BP RHdmi Appendix 3 Parental Guidance Codes Appendix 4 Glossary Page Appendix Accessories Auto code search Region Appendix 6 Instruction Guide for Programming Remote ControlProgramming Auto code search Brand code displayBrand Code Code list for European MarketRCA AOC Code list for USA MarketTMK Code list for China Market SSS Tobo Brand Code Memo Toshiba Corporation