Toshiba 32RV530U, 37RV530U, 52RV530U manual To connect the IR blaster cable, To control the devices

Page 15

Chapter 2: Connecting your TV

Connecting a device to the IR OUT infrared terminal using the IR blaster cable for IR pass-through device control

You can use the TV’s IR OUT terminal (infrared pass- through) to remotely operate (through the TV) many infrared remote-controlled devices (such as Toshiba infrared remote- controlled VCRs or DVD players) enclosed within an entertainment center or similar cabinet. Without the IR OUT connection, the device typically would need to be visible to operate it remotely.

You will need:

•dual-wand IR blaster cable (- page 12)

•other audio/video cables as required to connect the device(s) to the TV (- pages 13–16)

Front of IR-controlled DVD player (for example)

Front of IR-controlled audio device (for example)

Infrared sensor

IR blaster cable wand (approx.1 inch from device)

TV upper back panel

To connect the IR blaster cable:

1 Locate the infrared sensor on the front of your device. This sensor is marked on some devices.*

2 Align one of the IR blaster cable’s wands about 1 inch away from the infrared sensor on the front of the device and attach it using double-sided mounting tape. If you have a second device, attach the second wand in a similar manner. (See illustration.)

Note: If you do not have a second device, coil the second wand with a rubber band and leave it behind the TV.

3 Plug the IR blaster cable’s plug into the TV’s IR OUT terminal.

To control the device(s):

Point either the device’s remote control or the TV remote control (that you previously programmed to operate the device; - Chapter 3) toward the front of the TV and press the button for the desired function. The signal passes from the remote control through the TV to the device via the IR blaster cable.

Note:

•If you use the device’s remote control to operate the device, you also will need to use the TV’s remote control to operate the TV.

•The IR pass-through feature does not support all IR-controlled devices; satisfactory performance may not be attainable with certain devices.

*If you cannot locate the device’s infrared sensor:

1Turn OFF the device.

2Starting at the lower left corner of the device, place the end of the device’s remote control (with the infrared emitter) so it touches the front of the device and press POWER. (Do not use the TV’s remote control for this step.)

3If the device turns on, the point at which the remote control touched the device is the location of the sensor.

4If the device does not turn on, move the remote control slightly to the right and press POWER again.

5Repeat step 4 until you locate the device’s infrared sensor.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 32RV530U 37RV530U 42RV530U 46RV530U 52RV530U Dear Customer Safety PrecautionsIssue Tune Into SafetyInstallation Important Safety InstructionsInstallation, Care, and Service Additional Safety PrecautionsCare ServiceRemoving the Pedestal Stand To Display your LCD TV using a Wall BracketChoosing a location for your LCD TV To Display your LCD TV on the included Pedestal StandPart Important notes about your LCD TVTrademark Information Contents Troubleshooting Introduction Features of your new TVTV front and side panel controls and connections Effective rangeGreen and Yellow LEDs TV back panel connections Connecting your TV Overview of cable types About the connection illustrations To view the VCR To view the antenna or Cable signalYou will need To view basic and premium Cable channelsTo record a TV program while watching a DVD To view antenna or Cable channelsTo view the DVD player To view the VCR or view and record antenna channelsTo connect the IR blaster cable To control the devicesIf you cannot locate the device’s infrared sensor To connect a DVI device, you will need Connecting an Hdmi or DVI device to the Hdmi inputTo connect an Hdmi device, you will need To view the Hdmi device videoBefore controlling the devices REGZA-LINK connectionTo control the audio Connecting an audio systemTo connect a PC to the Hdmi terminal on the TV Connecting a personal computer PCSignal To connect a PC to the PC in terminal on the TVIf you have a Toshiba device Using the remote controlPreparing the remote control for use Installing the remote control batteriesLearning about the remote control AUX Using the remote control to control your other devicesTo use your TV remote control to operate a VCR, set the Mode Select switch to AUXAUX 1 VCR Remote Control functional key chartProgramming the remote control to control your other devices DVD/VCR Combo Cable converter boxSatellite receiver TV/VCR ComboHtib Icon Setup/Installation menu layoutMenu layout and navigation Main menu layoutApplications Navigating the menu systemSelecting the menu language Setting up your TVTo configure the ANT/CABLE input source Input Configuration, and press TManually adding and deleting channels in the channel memory Programming channels automaticallyLabeling channels To delete the custom label Setting the Hdmi audio modeTo set the Hdmi audio mode To create and assign a custom labelSetting the time zone Viewing the digital signal meterSelecting the Power-On Mode Reset Factory DefaultsViewing the system status To select the video input source to view Using the TV’s featuresSelecting the video input source to view Labeling the video input sourcesTuning channels Tuning channels using Channel BrowserFavorites Browser Elements of the Channel Browser Adding and clearing channels and inputs in the History List Setting the Channel Tuning ModeTuning to the next programmed channel Tuning to a specific channel programmed or unprogrammedTo select the picture size using the menus Switching between two channels using Channel ReturnSwitching between two channels using SurfLock To select the picture size using the remote controlTheaterWide For letter box programs with subtitles Picture Size NaturalTheaterWide For 43 format programs TheaterWide For letter box programsTo turn off the auto aspect ratio feature Using the auto aspect ratio featureTo set the scroll settings To turn on the auto aspect ratio featureAdjusting the picture quality Using the Freeze featureAdjusting the picture Selecting the picture modeBase closed captions Using the TheaterLock featureUsing the closed caption mode Digital CC SettingsMuting the sound Adjusting the audioUsing the digital audio selector CC SelectorSelecting stereo/SAP broadcasts Adjusting the audio qualityTo adjust the audio quality To turn off the StableSound featureIf you cannot remember your PIN code Using the Locks menuControl feature Entering the PIN codeTo block and unblock TV programs and movies Press b to highlight Enable Rating BlockingChanging your PIN code Blocking TV programs and movies by rating V-ChipUnlocking programs temporarily Blocking channelsUsing the input lock feature Using the GameTimerUsing the control panel lock feature To set the PC Audio Using the PC settings featureSetting the PC Audio To adjust the PC settingsSetting the sleep timer Using REGZA-LINKREGZA-LINK playback device HD DVD player, etc. control REGZA-LINK Player Control menu functions Volume and Mute controls of Audio ReceiverREGZA-LINK input source selection Other REGZA-LINK functionsUsing the Hdmi settings feature To set the REGZA-LINK SetupTo set the Hdmi Settings To display TV status information using Info Understanding the auto power off featureUnderstanding the last mode memory feature To display TV status information using RecallUsing the static gamma feature Using the TV’s advanced featuresUsing the advanced picture settings features Using dynamic contrastSelecting the color temperature Using CableClear digital noise reductionUsing Mpeg noise reduction Using the ColorMaster feature Using the Game Mode featureUsing Color Palette Adjustment Off Using the advanced audio settings featuresUsing the surround sound features To adjust the settingsGeneral troubleshooting TroubleshootingRating blocking V-Chip problems Remote control problemsChannel tuning problems Closed caption problemsLED indications Appendix SpecificationsFormat Resolution Frequency Pixel Clock Frequency Acceptable signal formats for PC in and Hdmi terminalsFor LCD Televisions 26 and Larger Limited United States WarrantyFor Toshiba Brand Flat Panel Televisions Limited Canadian WarrantyDisclaimer and Limitation of Remedy Appendix Freeze IndexPage Page Page Page Page 08-01
Top Page Image Contents