Toshiba 42RV530U, 32RV530U, 37RV530U Programming the remote control to control your other devices

Page 24

While holding down E, press the Channel Number buttons to enter the 3-digit code for your device.

Chapter 3: Using the remote control

Programming the remote control to control your other devices

Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote control to operate a non-Toshiba device (or a Toshiba device that it is not preprogrammed to operate), follow the steps below. For details on using the remote control to operate the device, see page 22.

1 In the remote control code table (- page 25), find the code for your device. If more than one code is listed, try each one separately until you find one that works.

2 Set the MODE SELECT switch to the type of device you are programming the remote control to operate — CABLE/SAT (for a cable converter box or satellite receiver), AUX 1 (for a VCR or TV/VCR combo), or AUX 2 (for a DVD player or HTIB [home theater in a box]).

3

4 To test the code, turn on the device, point the remote control at it, and press p. See notes below.

5

6

•If the correct code was entered, the device will turn off.

•If the device does not respond, repeat steps 1–4 using another code.

•If the device does not respond to another code, you will need to use the remote control that came with the device.

Remember to set the MODE SELECT switch back to “TV” to control the TV.

For future reference, write down the code(s) you used:

DEVICE CODE

DEVICE CODE

Note:

•In addition to POWER, confirm that all necessary keys on the TV remote control operate your device. If some keys are not operational, repeat the device code setup using another code (if other codes are listed for your device). If, after trying all listed codes, the necessary keys do not operate your device, use the device’s original remote control.

•Every time you change the batteries, you will need to reprogram the remote control.

•Some newer VCRs respond to either of two codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch and does not respond to the codes for your VCR brand, set the switch to the other position (“VCR1” or “VCR2”) and reprogram the remote control.

24

Image 24

Contents 32RV530U 37RV530U 42RV530U 46RV530U 52RV530U Safety Precautions IssueTune Into Safety Dear CustomerImportant Safety Instructions Installation, Care, and ServiceAdditional Safety Precautions InstallationService CareTo Display your LCD TV using a Wall Bracket Choosing a location for your LCD TVTo Display your LCD TV on the included Pedestal Stand Removing the Pedestal StandPart Important notes about your LCD TVTrademark Information Contents Troubleshooting Features of your new TV IntroductionTV front and side panel controls and connections Effective rangeGreen and Yellow LEDs TV back panel connections Connecting your TV Overview of cable typesAbout the connection illustrations To view the antenna or Cable signal You will needTo view basic and premium Cable channels To view the VCRTo view antenna or Cable channels To view the DVD playerTo view the VCR or view and record antenna channels To record a TV program while watching a DVDTo connect the IR blaster cable To control the devicesIf you cannot locate the device’s infrared sensor Connecting an Hdmi or DVI device to the Hdmi input To connect an Hdmi device, you will needTo view the Hdmi device video To connect a DVI device, you will needREGZA-LINK connection Before controlling the devicesConnecting an audio system To control the audioConnecting a personal computer PC SignalTo connect a PC to the PC in terminal on the TV To connect a PC to the Hdmi terminal on the TVUsing the remote control Preparing the remote control for useInstalling the remote control batteries If you have a Toshiba device Learning about the remote control Using the remote control to control your other devices To use your TV remote control to operate aVCR, set the Mode Select switch to AUX AUXRemote Control functional key chart AUX 1 VCRProgramming the remote control to control your other devices Cable converter box Satellite receiverTV/VCR Combo DVD/VCR ComboHtib Setup/Installation menu layout Menu layout and navigationMain menu layout IconNavigating the menu system ApplicationsSetting up your TV To configure the ANT/CABLE input sourceInput Configuration, and press T Selecting the menu languageProgramming channels automatically Manually adding and deleting channels in the channel memoryLabeling channels Setting the Hdmi audio mode To set the Hdmi audio modeTo create and assign a custom label To delete the custom labelViewing the digital signal meter Setting the time zoneSelecting the Power-On Mode Reset Factory DefaultsViewing the system status Using the TV’s features Selecting the video input source to viewLabeling the video input sources To select the video input source to viewTuning channels Tuning channels using Channel BrowserFavorites Browser Elements of the Channel Browser Setting the Channel Tuning Mode Tuning to the next programmed channelTuning to a specific channel programmed or unprogrammed Adding and clearing channels and inputs in the History ListSwitching between two channels using Channel Return Switching between two channels using SurfLockTo select the picture size using the remote control To select the picture size using the menusPicture Size Natural TheaterWide For 43 format programsTheaterWide For letter box programs TheaterWide For letter box programs with subtitlesUsing the auto aspect ratio feature To set the scroll settingsTo turn on the auto aspect ratio feature To turn off the auto aspect ratio featureUsing the Freeze feature Adjusting the pictureSelecting the picture mode Adjusting the picture qualityUsing the TheaterLock feature Using the closed caption modeDigital CC Settings Base closed captionsAdjusting the audio Using the digital audio selectorCC Selector Muting the soundAdjusting the audio quality To adjust the audio qualityTo turn off the StableSound feature Selecting stereo/SAP broadcastsUsing the Locks menu Control featureEntering the PIN code If you cannot remember your PIN codePress b to highlight Enable Rating Blocking Changing your PIN codeBlocking TV programs and movies by rating V-Chip To block and unblock TV programs and moviesBlocking channels Unlocking programs temporarilyUsing the input lock feature Using the GameTimerUsing the control panel lock feature Using the PC settings feature Setting the PC AudioTo adjust the PC settings To set the PC AudioSetting the sleep timer Using REGZA-LINKREGZA-LINK playback device HD DVD player, etc. control Volume and Mute controls of Audio Receiver REGZA-LINK input source selectionOther REGZA-LINK functions REGZA-LINK Player Control menu functionsUsing the Hdmi settings feature To set the REGZA-LINK SetupTo set the Hdmi Settings Understanding the auto power off feature Understanding the last mode memory featureTo display TV status information using Recall To display TV status information using InfoUsing the TV’s advanced features Using the advanced picture settings featuresUsing dynamic contrast Using the static gamma featureSelecting the color temperature Using CableClear digital noise reductionUsing Mpeg noise reduction Using the ColorMaster feature Using the Game Mode featureUsing Color Palette Adjustment Using the advanced audio settings features Using the surround sound featuresTo adjust the settings OffTroubleshooting General troubleshootingRemote control problems Channel tuning problemsClosed caption problems Rating blocking V-Chip problemsLED indications Specifications AppendixAcceptable signal formats for PC in and Hdmi terminals Format Resolution Frequency Pixel Clock FrequencyLimited United States Warranty For LCD Televisions 26 and LargerLimited Canadian Warranty For Toshiba Brand Flat Panel TelevisionsDisclaimer and Limitation of Remedy Appendix Index FreezePage Page Page Page Page 08-01