Toshiba 40RV525U, 46RV525U Programming channels automatically, To program channels automatically

Page 31

Chapter 5: Setting up your TV

Programming channels into the TV’s channel memory

When you press or on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV’s channel memory.

Follow the steps below to program channels into the TV’s channel memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory.

Note:

You must configure the ANT/CABLE input source before

programming channels ( page 30).

The automatic channel programming process will erases channels that were previously programmed into the TV’s memory.

To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

Programming channels when the ANT/CABLE input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly.

To program channels automatically:

1 Configure the antenna input source, if you have not already done so ( page 30).

2 Press and open the Setup menu.

3 Highlight Installation and press .

Setup

Installation

HDMI Control Setup

Sleep Timer

PC Settings

Logo LED

Off

4 (A new set of Installation menu icons will appear, as shown below.) Open the Terrestrial menu, highlight Channel Program to bring up the Start, and press again to begin channel programming.

The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above).

5 To cancel channel programming, press on the remote control (or highlight Cancel in the on-screen display and press ).

When channel programming is finished, press or to view the programmed channels.

Manually adding and deleting channels in the channel memory

After automatically programming channels into the channel memory, you can manually add or delete individual channels.

To add or delete channels in the channel memory:

1 From the Setup menu, highlight Installation and press . A new set of Installation menu icons will appear.

2 Open the Terrestrial menu, highlightChannel Add/ Delete, and then press .

To add a channel to the channel memory:

Highlight the unchecked box next to the channel number you want to add, and then press to check the box.

(continued)

31

Image 31
Contents 40RV52U 40RV525U 46RV525U Dear Customer Safety PrecautionsIssue Tune Into SafetyInstallation Important Safety InstructionsInstallation, Care, and Service Additional Safety PrecautionsCare ServiceRemoving the Pedestal Stand To Display your LCD TV using a Wall BracketChoosing a location for your LCD TV To Display your LCD TV on the included Pedestal StandImportant notes about your LCD TV PartTrademark Information Contents Introduction Features of your new TVIntroduction Green LED and Toshiba Logo LED TV front and side panel controls and connectionsTV back panel connections Overview of cable types Connecting your TVTo view the VCR Connecting a VCR and antenna or Cable TV no Cable boxTo view the antenna or Cable signal You will needStandard audio cables Connecting a VCR with S-video and a cable boxTo view basic and premium Cable channels Coaxial cables Video cableTo record a TV program while watching a DVD To view antenna or Cable channelsTo view the DVD player To view the VCR or view and record antenna channelsTo view the camcorder video Connecting a camcorderSelect the Video 2 video input source on the TV To connect a DVI device, you will need One Hdmi cable type a connector per Hdmi deviceTo connect an Hdmi device, you will need To view the Hdmi device videoBefore controlling the devices Hdmi Control connectionTo control the audio Connecting an audio systemTo connect a PC to the Hdmi terminal on the TV Connecting a personal computer PCPin No Signal To connect a PC to the PC in terminal on the TVRemote control effective range Using the remote controlPreparing the remote control for use Installing the remote control batteriesDot TheaterWide 1/2/3, Full, 43 HD, Native and Dot byAUX To use your TV remote control to operate aVCR, set the Mode Select switch to AUX DVD player or HTIB, set the Mode Select switch toAUX 1 VCR Remote Control functional key chartProgramming the remote control to control your other devices DVD/VCR Combo Cable converter boxSatellite receiver TV/VCR ComboHtib Main menu layout Menu layout and navigationIcon Option Channel Program Start p Scans for new channels on Setup/Installation menu layoutInput Configuration Opens the Input Configuration menu Navigating the menu systemToshiba Logo LED Setting up your TVTo configure the ANT/CABLE input source Selecting the menu languageTo add or delete channels in the channel memory Programming channels automaticallyManually adding and deleting channels in the channel memory To program channels automaticallyLabeling channels To delete the custom label Setting the Hdmi audio modeTo set the Hdmi audio mode To create and assign a custom labelViewing the system status Viewing the digital signal meterSetting the time zone Reset Factory DefaultsTo select the video input source to view Using the TV’s featuresSelecting the video input source to view Labeling the video input sourcesTuning channels using Channel Browser Tuning channelsFavorites Browser Elements of the ChannelBrowser Adding and clearing channels and inputs in the History List Setting the Channel Tuning ModeTuning to the next programmed channel Tuning to a specific channel programmed or unprogrammedTo select the picture size using the menus Switching between two channels using Channel ReturnSwitching between two channels using SurfLock To select the picture size using the remote controlTheaterWide For letter box programs with subtitles NaturalTheaterWide For 43 format programs TheaterWide For letter box programsUsing the Freeze feature Selecting the cinema modeTo select the picture mode using the menu system Adjusting the pictureSelecting the picture mode Adjusting the picture qualityCC Selector Using the closed caption modeDigital CC Settings Base closed captionsSelecting stereo/SAP broadcasts Adjusting the audioUsing the digital audio selector Muting the soundTo select the optical audio output format Adjusting the audio qualityUsing the Dolby Digital Dynamic Range Control feature To adjust the audio qualityChanging your PIN code Using the Locks menuEntering the PIN code If you cannot remember your PIN codeTo download the additional rating system if available Blocking channels Using the input lock featureUnlocking programs temporarily Using the GameTimer Using the PC settings featureUsing the control panel lock feature Setting the sleep timer Setting the PC AudioUsing Hdmi Control To display TV status information using Info Understanding the auto power off featureUnderstanding the last mode memory feature To display TV status information using RecallSelecting the color temperature Using the TV’s advanced featuresUsing dynamic contrast Using the static gamma featureUsing the Game Mode feature Using Mpeg noise reductionHighlight Advanced Audio Settings and press Using the advanced audio settings featuresUsing the QSound sound feature To adjust the QSound settingsGeneral troubleshooting TroubleshootingHdmi problems Channel tuning problemsClosed caption problems Rating blocking V-Chip problemsAppendix SpecificationsFormat Resolution Frequency Pixel Clock Frequency Acceptable signal formats for PC in and Hdmi terminalsFor LCD Televisions 26 and Larger Limited United States WarrantyFor Toshiba Brand Flat Panel Televisions Limited Canadian WarrantyDisclaimer and Limitation of Remedy Appendix Page Toshiba America Consumer PRODUCTS, L.L.C