Toshiba 34HFX84 owner manual Connecting an audio system

Page 15

Connecting an audio system

This connection allows you to use an audio amplifier and external speakers, and adjust the audio level using the TV’s remote control.

To control the audio, turn on the TV and the stereo amplifier, and turn off the TV’s built-in speakers (see “Turning off the built-in speakers” on page 57).

You will need:

• one pair of standard audio cables

TV

Note:

To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set above 0 (zero).

For example, if the volume of the TV is set to 0, you will not be able to hear any sound, even the volume of the amplifier is at its highest level.

Amplifier

LINE IN

L R

Introduction

 

 

 

 

 

Connecting

yourTV

 

 

 

 

Usingthe

RemoteControl

 

 

 

 

Settingup

yourTV

 

 

 

 

UsingtheTV’s

Features

 

 

 

 

Appendix

 

 

 

 

 

Index

 

 

 

15

Image 15
Contents Color Television Dear Customer Safety PrecautionsInstallation Important Safety InstructionsCare ServiceImportant Safety Information Introduction Welcome to Toshiba Exploring your new TVIntroduction Appendix Index Connecting an antenna or cable TVYou will need Three coaxial cables Connecting a VCRConnecting a cable converter box Connecting your TVUsingtheTV’s Features Connecting a cable converter box and VCRSatellite Receiver Connecting a DVD player or satellite receiver and a VCRFrom Antenna Stereo VCR From DTV Antenna Connecting two VCRs Connecting a camcorderUsing One pair of standard analog audio cables Connecting an Hdmi or a DVI device to the Hdmi inputOne Hdmi cable type a connector One HDMI-to-DVI adapter cable Hdmi type a connectorConnecting an audio system Preparing the remote control for use Installing the remote control batteriesUsing the Remote Control Remote Control functional key chart CBL/SAT Audio VCR TV/VCR TV/SAT Searching and sampling the code of a device Device code setupIntroduction Connecting YourTV Usingthe RemoteControl Settingup YourTV UsingtheTV’s Features Appendix IndexOperational feature reset Using the volume lock featureDevice code table VCR setup codesCD Player setup codes Learning about the remote control Learning about the menu system Setting up your TVSelecting the antenna input Changing the on-screen display languagePress Enter Press z to select CH Program Adding channels to the TV’s memoryProgramming channels automatically To program channels automaticallyAdding and erasing channels manually Adjusting the tilt correction featureConnecting yourTV Changing channelsSwitching between two channels using SurfLock Adjusting the channel settingsUsing the TV’s Features Switching between two channels using Channel ReturnPress y or z to highlight Connecting Your Usingthe RemoteControlSettingup yourTV Press Enter Repeat steps 4 and 5 for other channelsLabeling channels ClearPress Enter to erase the channel label Selecting the picture size Usingthe FeaturesTheater Wide 1 picture size For 43 format program Press Enter to display the Scroll Adjustment mode To raise the picture, press yTo lower the picture, press z Using the Auto Aspect feature Press y or z to highlight Auto ASPECT, and then pressPress y or z to select ON, and then press Enter Settingup YourTV UsingtheTV’s Features Appendix Using the POP double-window featureSwitching the speaker audio main or POP Switching the main and POP picturesDouble-Window aspect ratio Using the programmed channel search functionAbout the auto favorite feature Using the favorite channel search functionIf you cannot remember your PIN code Using the Locks menuUsing the V-CHIP menu Entering the PIN codePress z or y to select an item Enable BlockingOFF To release your setting Unlock TV Rating Independent rating system for broadcastersConnecting YourTV Usingthe RemoteControl Settingup Mpaa Rating Independent rating system for moviesMpaa Rating Repeat steps 2 and 3 for other channels Locking channelsUnlocking programs temporarily Press EnterPress y or z to highlight Clear ALL, and then press Enter Press Enter New PIN code is now active Locking the video inputsChanging the PIN code OFFSetting Your UsingtheTV’s Features Appendix Index Adjusting the pictureIntroduction Connecting YourTV Usingthe RemoteControlSaving your new preferences Selecting the color temperaturePicture Settings menu appears Press x or to select the mode you preferSelecting the Scan Velocity Modulation SVM Using the CableClear DNR featureReset Resetting picture adjustmentsSelecting the display format for 480p signals only Selecting the cinema modeSelecting the video input source Using the closed caption feature Press y or z to highlight Caption or TEXT, and then pressTo view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timerSetting the clock Press Enter to start the clockTo display the time on-screen Press Recall Selecting stereo/SAP broadcasts Adjusting the soundUsingthe Remote Settingup YourTV Muting the soundEnjoying the Dolby Virtual sound feature Audio Settings menu appears Using the WOW surround sound featureAdjusting the sound quality Press y or z to adjust the item, then press EnterCenter Resetting your audio adjustmentsUsing the StableSound feature To turn off the StableSound feature Select OFF in aboveConnecting Your Control Turning off the built-in speakersSelecting the Audio OUT sound Using the Cyclone sub-woofer system Displaying on-screen information Understanding the auto power off featureUnderstanding the last mode memory feature Selecting the background of the menu displayAppendix SpecificationsT2, T3, or T4. Turn closed captioning OFF TroubleshootingAntenna Black box appears on the screenLimited United States Warranty Limited Canada Warranty Index Page Page Page Manufactured by