Toshiba 34HFX84 Device code setup, Introduction Connecting YourTV Usingthe RemoteControl

Page 19

Programming the remote control for use with your audio/video devices

Device code setup

1.Refer to the Device code table on pages 21–22 to find the code for your device.

If more than one number is listed, try each one separately until you find one that works.

2.Press MODE until the Mode indicator for the device (CABLE/ SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.

3.While holding down the RECALL button, press the Channel Number buttons to enter the four-digit code for your device. If a valid code is entered, the mode indicator will blink twice. If an invalid code is entered, the mode indicator will blink one long blink.

4.Point the remote control at the device and press POWER to test the code.

If the device turns on, you have entered the correct code.

If the device does not respond to the remote control, you may have entered the wrong code. Repeat steps 3 and 4 using another code.

5.Press MODE to select the TV mode to control the TV.

Note:

•Every time you replace the batteries, you must reprogram the remote control.

•Some newer VCRs are capable of working on either of two remote codes.These VCRs have a switch labeled “VCR1/VCR2.”

If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control

Introduction

 

 

 

 

 

Connecting

yourTV

 

 

 

 

Usingthe

RemoteControl

 

 

Searching and sampling the code of a device (8500)

TV

POWER

If you do not know the device code for a particular target unit, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that properly operates the target device. The keys available to be sampled, provided they are applicable to that mode, are POWER, 1, VOL y, CH y, and PLAY. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1.Press MODE to select the mode you want to set up.

2.While holding down the RECALL button, press 8 –5 –0 –0. The remote control will enter program mode.

3.Point the remote control at the target device and press POWER (or other function buttons that are available to be sampled).

4.If the device responds to the remote control:

Press RECALL to store the device code.

The mode indicator will blink twice and the remote control will exit the program mode.

If the device does not respond to the remote control: Press y, and then press POWER.

Repeat this step until the device responds to the remote control, and then press RECALL.

Note: When a search cycle is completed, the mode indicator will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

CABLE/SAT LIGHT SLEEP POWER

VCR

 

DVD

1 2 3

AUDIO1Numbers

AUDIO2

4

5

6

 

 

 

MODE

 

 

 

 

 

 

 

 

MODE

 

 

 

7

 

 

8

9

 

 

PIC SIZE

 

+10

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

ACTION

 

100/

 

 

ENT

 

 

MENU

 

O

FAV

ORI

 

 

 

 

 

 

NF

 

 

T

 

 

 

 

 

I

 

 

 

TE

 

 

 

 

 

 

 

 

 

 

HE

 

 

E

 

 

 

 

 

 

LI

AT

 

 

 

 

 

 

 

 

E

ID

 

 

 

 

 

 

N

 

R

U

 

 

 

 

 

 

 

K

 

 

G

 

 

LE

SUB

TIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIT

 

 

 

 

 

 

P

 

 

 

 

LE

A

 

 

 

 

U

 

 

 

 

 

U

 

 

 

T

 

FAV

 

 

DI

 

 

y

S

 

 

 

 

 

 

 

E

 

 

 

 

O

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER

 

 

 

 

 

 

 

 

 

FAV

 

 

 

 

 

 

CH

 

 

 

 

 

VOL

 

 

 

DVD RTN

 

EXIT

 

 

 

 

 

RECALL

 

DVD CLEAR

 

 

 

 

CH RTN

 

INPUT

RECALL

MUTE

 

 

SLOW/DIR SKIP/SEARCH

Settingup

yourTV

 

 

UsingtheTV’s

Features

 

 

 

 

Appendix

 

 

 

 

 

Index

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Color Television Dear Customer Safety PrecautionsInstallation Important Safety InstructionsCare ServiceImportant Safety Information Introduction Exploring your new TV Welcome to ToshibaIntroduction Appendix Index Connecting an antenna or cable TVYou will need Three coaxial cables Connecting a VCRConnecting a cable converter box Connecting your TVUsingtheTV’s Features Connecting a cable converter box and VCRSatellite Receiver Connecting a DVD player or satellite receiver and a VCRFrom Antenna Stereo VCR From DTV Antenna Connecting a camcorder Connecting two VCRsUsing One pair of standard analog audio cables Connecting an Hdmi or a DVI device to the Hdmi inputOne Hdmi cable type a connector One HDMI-to-DVI adapter cable Hdmi type a connectorConnecting an audio system Installing the remote control batteries Preparing the remote control for useUsing the Remote Control Remote Control functional key chart CBL/SAT Audio VCR TV/VCR TV/SAT Searching and sampling the code of a device Device code setupIntroduction Connecting YourTV Usingthe RemoteControl Settingup YourTV UsingtheTV’s Features Appendix IndexOperational feature reset Using the volume lock featureDevice code table VCR setup codesCD Player setup codes Learning about the remote control Learning about the menu system Setting up your TVSelecting the antenna input Changing the on-screen display languagePress Enter Press z to select CH Program Adding channels to the TV’s memoryProgramming channels automatically To program channels automaticallyAdding and erasing channels manually Adjusting the tilt correction featureConnecting yourTV Changing channelsSwitching between two channels using SurfLock Adjusting the channel settingsUsing the TV’s Features Switching between two channels using Channel ReturnPress y or z to highlight Connecting Your Usingthe RemoteControlSettingup yourTV Press Enter Repeat steps 4 and 5 for other channelsClear Labeling channelsPress Enter to erase the channel label Selecting the picture size Usingthe FeaturesTheater Wide 1 picture size For 43 format program To raise the picture, press y Press Enter to display the Scroll Adjustment modeTo lower the picture, press z Press y or z to highlight Auto ASPECT, and then press Using the Auto Aspect featurePress y or z to select ON, and then press Enter Settingup YourTV UsingtheTV’s Features Appendix Using the POP double-window featureSwitching the speaker audio main or POP Switching the main and POP picturesDouble-Window aspect ratio Using the programmed channel search functionAbout the auto favorite feature Using the favorite channel search functionIf you cannot remember your PIN code Using the Locks menuUsing the V-CHIP menu Entering the PIN codePress z or y to select an item Enable BlockingOFF To release your setting Unlock TV Rating Independent rating system for broadcastersMpaa Rating Independent rating system for movies Connecting YourTV Usingthe RemoteControl SettingupMpaa Rating Repeat steps 2 and 3 for other channels Locking channelsUnlocking programs temporarily Press EnterPress y or z to highlight Clear ALL, and then press Enter Press Enter New PIN code is now active Locking the video inputsChanging the PIN code OFFSetting Your UsingtheTV’s Features Appendix Index Adjusting the pictureIntroduction Connecting YourTV Usingthe RemoteControlSaving your new preferences Selecting the color temperaturePicture Settings menu appears Press x or to select the mode you preferSelecting the Scan Velocity Modulation SVM Using the CableClear DNR featureReset Resetting picture adjustmentsSelecting the display format for 480p signals only Selecting the cinema modeSelecting the video input source Press y or z to highlight Caption or TEXT, and then press Using the closed caption featureTo view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timerPress Enter to start the clock Setting the clockTo display the time on-screen Press Recall Selecting stereo/SAP broadcasts Adjusting the soundUsingthe Remote Settingup YourTV Muting the soundEnjoying the Dolby Virtual sound feature Audio Settings menu appears Using the WOW surround sound featureAdjusting the sound quality Press y or z to adjust the item, then press EnterCenter Resetting your audio adjustmentsUsing the StableSound feature To turn off the StableSound feature Select OFF in aboveTurning off the built-in speakers Connecting Your ControlSelecting the Audio OUT sound Using the Cyclone sub-woofer system Displaying on-screen information Understanding the auto power off featureUnderstanding the last mode memory feature Selecting the background of the menu displayAppendix SpecificationsT2, T3, or T4. Turn closed captioning OFF TroubleshootingAntenna Black box appears on the screenLimited United States Warranty Limited Canada Warranty Index Page Page Page Manufactured by
Top Page Image Contents