Integra DPC-8.5 instruction manual Precautions, FCC Information for User Caution

Page 3

Precautions

DANGER:

VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED OR DEFEATED. DO NOT STARE INTO BEAM.

FCC INFORMATION FOR USER CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION:

THIS PRODUCT UTILIZES A LASER. USE OF CON- TROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI- FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

This unit contains a semiconductor laser system and is classified as a “CLASS 1 LASER PRODUCT.” So, to use this model properly, read this Instruction Manual carefully. In case of any trouble, please contact the store where you purchased the unit. To prevent exposure to the laser beam, do not try to open the enclosure.

In some cases, this label is located on the rear panel. It indicates that:

1.This unit is a CLASS 1 LASER PRODUCT and employs a laser inside the cabinet.

2.To prevent the laser from being exposed, do not remove the cover. Refer servicing to qualified person- nel.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence in a residential installation. This equipment gener- ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communi- cations. However, there is no guarantee that interference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit dif- ferent from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV techni- cian for help.

For U.S. model

The laser is covered by a housing which prevents expo- sure during operation or maintenance. However, this product is classified as a Laser Product by CDRH (Cen- ter for Devices and Radiological Health) which is a department of the Food and Drug Administration.

According to their regulations 21 CFR section 1002.30, all manufactures who sell Laser Products must maintain records of written communications between the manu- facturer, dealers and customers concerning radiation safety. If you have any complaints about instructions or explanations affecting the use of this product, please feel free to write to the address on the back page of this man- ual. When you write us, please include the model num- ber and serial number of your unit.

In compliance with Federal Regulations, the certifica- tion, identification and the period of manufacture are indicated on the rear panel.

For Canadian model

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

NOTE: This Class B digital apparatus complies with Canadian ICES-003.

Modèle canadien

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.

3

Image 3
Contents DPC-8.5 Avis Important Safety InstructionsFCC Information for User Caution PrecautionsPrecautions Connecting the DPC-8.5 Contents Supplied Accessories Power cordIntroduction Audio Introduction DPC-8.5 FeaturesHighlights VideoIntroduction Disc Notes Disc Content Organization IntroductionMP3 & Jpeg Compatibility Copyright TerminologyHandling Discs Storing DiscsJpeg Joint Photographic Experts Group Vlsc Vector Linear Shaping CircuitryMPEG2 Moving Picture Experts Group Open the battery compartment, as shown Before Using the DPC-8.5Installing the Remote’s Batteries Using the Remote ControllerFront Panel Getting to Know the DPC-8.5Getting to Know the DPC-8.5 Display Rear Panel Getting to Know the DPC-8.5IR IN/OUT RS232 portGetting to Know the DPC-8.5 Remote Controller Enter button Setup buttonClear button 33, 36 Menu buttonOptical Digital Output Connecting the DPC-8.5AV Cables & Connectors Before Making Any ConnectionsConnecting Your TV or Projector Connecting the DPC-8.5AV cable Supplied SuppliedDigital Audio Connection Dolby Digital & DTS Connecting the DPC-8.5 Connecting an AV ReceiverDigital Connection Connecting the DPC-8.5 Connecting a Stereo AmpConnecting Components with Analog ConnectionControlling Other Out-of-range Components Controlling the DPC-8.5 When It’s Out of RangeDPC-8.5’s AC Inlet Connecting the DPC-8.5 Connecting the Power CordPlug the supplied power cord into Plug the other end of the power cord intoTurning On the DPC-8.5 & First Time Setup First Time SetupTurning On the DPC-8.5 Use the Left and Right Turning On the DPC-8.5 & First Time SetupLoading Discs Basic PlaybackBasic Playback Selecting DiscsLoading Discs During Playback Start To start playback, press the Play Button Starting, Pausing & Stopping PlaybackPause To pause playback, press the Pause buttonNavigating Disc Menus Load and select a DVD-VideoDVD-Audio, or VCD disc Selecting Titles & Chapters by Number Using the Disc Navigator Memory Playback in the Disc Navigator Selecting Tracks by Number Frame-by-Frame Playback Basic Playback Fast Forward & ReverseSlow-motion Playback Adjusting the Display BrightnessUsing Jpeg CDs To stop the slideshow, press the Stop or Menu button Using Chain ModeAdvanced Playback Time SearchRepeat Playback Advanced Playback Advanced Playback Random Playback Repeat steps 2 and 3 to add more Memory PlaybackItems to the list AngleInserting New Items into the Memory List Deleting Items from the Memory ListChanging Items in the Memory List Selecting Camera AnglesPress the Progressive button Using Progressive ScanningSelecting Languages & Audio Formats Selecting SubtitlesDisplaying Information Using Last Memory3rd press Normal1st press 2nd pressVCD & CD Advanced Playback Turning Off the Video Circuits Press the DPC-8.5’s Video Cir- cuit Off buttonTo turn the video circuitry back on, press the button again Language Menu Setting Description PictureConfiguring the DPC-8.5 AudioOperation Menu Setting DescriptionSetup Configuring the DPC-8.5Using the Onscreen Setup Menus Picture MenuTV Shape Interlaced Setting Progressive Setting Audio MenuDigital Out/Digital1 Optical Linear PCM Out Digital Out/Digital2 CoaxialAnalog Audio Out Setting the Speaker SettingsSetting the Speaker Distances Setting Levels With the Test Tone AV SynchronizationSelecting AV Synchronization Sacd Audio Setup CD Audio SetupDynamic Range Control Dolby Digital Only Audio Language Configuring the DPC-8.5 Language MenuOn-Screen Language Disc Menu LanguageOperation Menu Configuring the DPC-8.5 Display MenuPriority Contents Auto power offTitle/Group Stop Menu Language, Audio Lan Configuring the DPC-8.5 Initial Setup MenuLanguage Code List Selecting Other LanguagesSymptom Possible cause Remedy TroubleshootingTroubleshooting Restoring the Default SettingsAbnormal Behavior Specifications