Integra Before Using the DPC-7.4, Installing the Remote Controller’s Batteries

Page 15

Before Using the DPC-7.4

Installing the Remote Controller’s Batteries

1 Open the battery compartment, as shown.

Using the Remote Controller

To use the remote controller, point it at the DPC-7.4’s remote control sensor, as shown below.

Remote control sensor

DPC-7.4

2

Insert the two supplied batteries (AA/R6) in

 

 

accordance with the polarity diagram inside

30˚

 

the battery compartment.

30˚

DPC-7.4

 

 

 

(5

m)

 

 

 

 

 

 

.

 

 

16

ft

 

 

 

 

 

 

.

 

 

 

Approx

 

 

 

 

3

Close the battery compartment.

Notes:

The supplied batteries should last for about six months, although this will vary with usage.

If the remote controller doesn’t work reliably, try replacing both batteries.

Don’t mix new and old batteries, or different types of bat- teries.

If you intend not to use the remote controller for a long time, remove the batteries to prevent possible leakage and corrosion.

Flat batteries should be removed as soon as possible to pre- vent possible leakage and corrosion.

Notes:

The remote controller may not work reliably if the DPC-

7.4is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing the DPC-7.4.

If another remote controller of the same type is used in the same room, or the DPC-7.4 is installed close to equipment that uses infrared rays, the remote controller may not work reliably.

Don’t put anything, such as a book, on the remote control- ler, because the buttons may be pressed inadvertently, thereby draining the batteries.

The remote controller may not work reliably if the DPC-

7.4is installed in a rack behind colored glass doors. Keep this in mind when installing the DPC-7.4.

The remote controller will not work if there’s an obstacle between it and the DPC-7.4’s remote control sensor.

15

Image 15
Contents DPC-7.4 Contents Important Safety Instructions Precautions For models having a power cord with a polarized plugSur les modèles dont la fiche est polarisée Precautions Supplied Accessories DPC-7.4 FeaturesIntroduction DVD Region Numbers Supported Discs Unsupported DVD FeaturesDisc Content Organization Introduction Disc NotesMP3/WMA/JPEG Compatibility Cleaning DiscsIntroduction Video CDsDPC-7.4-related Terminology Storing DiscsCopyright Front Panel Controls & ConnectorsControls & Connectors Display IR IN/OUT Controls & Connectors Rear PanelControls & Connectors Remote Controller Controls & Connectors Before Using the DPC-7.4 Installing the Remote Controller’s BatteriesUsing the Remote Controller Optical Digital Inputs Connecting the DPC-7.4AV Cables & Connectors Before Making Any ConnectionsLets Connecting the DPC-7.4 Connecting Your TV or ProjectorPowering Up & Setting Up the DPC-7.4 on Turn off the DPC-7.4 and your TV, and disDigital Connection Connecting the DPC-7.4 Connecting Your Hi-Fi AmpConnecting for Dolby Digital or DTS Analog ConnectionPlug the supplied power cord into the AC Inlet Connecting the DPC-7.4 Connecting -compatible AV ComponentsControlling the DPC-7.4 When It’s Out of Range Controlling Other Out-of-range AV ComponentsConnect the IR receiver to the DPC-7.4 as shown below Powering Up & Setting Up the DPC-7.4 Powering Up the DPC-7.4First Time Setup Basic Playback Loading & Removing DiscsLoading Discs During Playback Starting, Pausing & Stopping Playback Basic PlaybackSelecting Discs Basic Playback Navigating Disc Menus Load and select a DVD-Video orVideo CD To start playback of the specified Selecting Titles & Chapters by NumberUse the number buttons to specify a chapter or title Press the Play or Enter buttonUsing the Disc Navigator To start memory playback, press the Play button Basic Playback Memory Playback in the Disc NavigatorWith the Disc Navigator open, press the Memory button Playlist appears in place of the file informationFast Forward & Reverse Selecting Tracks by NumberAdjusting the Display Brightness Slow-motion PlaybackFrame-by-Frame Playback Using Chain Mode Using Jpeg CDsAdvanced Playback Locating Specific Points in TimeRepeat Playback Random Playback Advanced PlaybackMemory Playback To cycle through the available cam- era angles Entire memory list is cleared when the DPC-7.4 is setSelecting Camera Angles To StandbyUsing Progressive Scanning Selecting Languages & Audio FormatsSelecting Subtitles Last Memory DisplayStop Play/Enter Using Last MemoryDuring playback, press the Last M button Last Memory dialog box appears, as shownPress the Display button again to Cancel the information displayAdvanced Playback Displaying Information During playback, press the DisConfiguring the DPC-7.4 Menu Setting Description PictureTV Shape Using the Onscreen Setup MenusConfiguring the DPC-7.4 Picture MenuInterlaced Setting PAL Output Setting Australian model onlyProgressive Setting Dynamic Range Control Dolby Digital only Configuring the DPC-7.4 Audio MenuLanguage Menu Digital OutDisplay Menu Parental Lock Operation Setting MenuScreen Saver Pause/StillSelecting Other Languages Language Code ListInitial Setup Menu Auto Power OffTroubleshooting Display? Buttons on the DPC-7.4 Remote controllerCan’t view Jpeg files? Message no Play appears onComponent Video Specifications