Integra instruction manual Connecting the DPC-7.4 Connecting -compatible AV Components

Page 19

Connecting the DPC-7.4—Continued

Connecting -compatible AV

Components

With (Remote Interactive) you can control your DPC-7.4 by using the remote controller supplied with your Onkyo or Integra -compatible AV receiver.

Integra/Onkyo AV receiver

REMOTE

DIGITAL IN

OPTICAL

CONTROL

 

L

 

R

ANALOG

INPUT

Plug the supplied power cord into the AC INLET

Do not use a power cord other than the one supplied with the DPC-7.4. The power cord supplied is designed for use with the DPC-7.4 and should not be used with any other device.

Never have the power cord disconnected from the DPC-7.4 while the other end is plugged into the wall outlet. Doing so may cause an electric shock. Always connect by plug- ging into the wall outlet last and disconnect by unplugging from the wall outlet first.

ANGER

. DPC-7.4

AC INLET

To use you must make an analog RCA/phono connection between the DPC-7.4 and the other component even if they are connected digitally.

cable (Supplied)

AUDIO OUTPUT

ANALOG

L

R

VIDEO OUTPUT

 

COMPONENT 2

 

Y

PB

 

PR

 

COMPONENT 1

 

 

Y

PB

PR

S VIDEO

AUDIO OUTPUT

ANALOG

VIDEO

LIN

IR

ROUT

AUDIO OUTPUT

DIGITAL

OPTICAL COAXIAL

REMOTE

CONTROL

DVD CHANGER

MODEL NO. DPC-7.4

AUDIO OUTPUT

RS 232

DIGITAL

OPTICAL COAXIAL

REMOTE

CONTROL

Notes:

Push the plugs in all the way to make a good connection.

Use only cables for connections.

To use you must also make an analog RCA/phono connection between your DPC-7.4 and Integra/Onkyo AV receiver, even if they are connected digitally.

The DPC-7.4 has two connectors. You can connect either one to your Integra/Onkyo AV receiver. The other connector is for connecting additional -compatible components.

Connect the DPC-7.4’s connector to only Integra/ Onkyo AV components. Connecting to other manufac- turer’s AV components may cause them to malfunction.

19

Image 19
Contents DPC-7.4 Contents Important Safety Instructions For models having a power cord with a polarized plug PrecautionsSur les modèles dont la fiche est polarisée Precautions DPC-7.4 Features Supplied AccessoriesIntroduction DVD Region Numbers Supported Discs Unsupported DVD FeaturesDisc Content Organization Introduction Disc NotesMP3/WMA/JPEG Compatibility Cleaning DiscsIntroduction Video CDsStoring Discs DPC-7.4-related TerminologyCopyright Front Panel Controls & ConnectorsControls & Connectors Display IR IN/OUT Controls & Connectors Rear PanelControls & Connectors Remote Controller Controls & Connectors Installing the Remote Controller’s Batteries Before Using the DPC-7.4Using the Remote Controller Optical Digital Inputs Connecting the DPC-7.4AV Cables & Connectors Before Making Any ConnectionsLets Connecting the DPC-7.4 Connecting Your TV or ProjectorPowering Up & Setting Up the DPC-7.4 on Turn off the DPC-7.4 and your TV, and disDigital Connection Connecting the DPC-7.4 Connecting Your Hi-Fi AmpConnecting for Dolby Digital or DTS Analog ConnectionPlug the supplied power cord into the AC Inlet Connecting the DPC-7.4 Connecting -compatible AV ComponentsControlling Other Out-of-range AV Components Controlling the DPC-7.4 When It’s Out of RangeConnect the IR receiver to the DPC-7.4 as shown below Powering Up the DPC-7.4 Powering Up & Setting Up the DPC-7.4First Time Setup Loading & Removing Discs Basic PlaybackLoading Discs During Playback Basic Playback Starting, Pausing & Stopping PlaybackSelecting Discs Basic Playback Load and select a DVD-Video or Navigating Disc MenusVideo CD To start playback of the specified Selecting Titles & Chapters by NumberUse the number buttons to specify a chapter or title Press the Play or Enter buttonUsing the Disc Navigator To start memory playback, press the Play button Basic Playback Memory Playback in the Disc NavigatorWith the Disc Navigator open, press the Memory button Playlist appears in place of the file informationFast Forward & Reverse Selecting Tracks by NumberSlow-motion Playback Adjusting the Display BrightnessFrame-by-Frame Playback Using Chain Mode Using Jpeg CDsLocating Specific Points in Time Advanced PlaybackRepeat Playback Random Playback Advanced PlaybackMemory Playback To cycle through the available cam- era angles Entire memory list is cleared when the DPC-7.4 is setSelecting Camera Angles To StandbySelecting Languages & Audio Formats Using Progressive ScanningSelecting Subtitles Last Memory DisplayStop Play/Enter Using Last MemoryDuring playback, press the Last M button Last Memory dialog box appears, as shownPress the Display button again to Cancel the information displayAdvanced Playback Displaying Information During playback, press the DisConfiguring the DPC-7.4 Menu Setting Description PictureTV Shape Using the Onscreen Setup MenusConfiguring the DPC-7.4 Picture MenuPAL Output Setting Australian model only Interlaced SettingProgressive Setting Dynamic Range Control Dolby Digital only Configuring the DPC-7.4 Audio MenuLanguage Menu Digital OutDisplay Menu Parental Lock Operation Setting MenuScreen Saver Pause/StillSelecting Other Languages Language Code ListInitial Setup Menu Auto Power OffTroubleshooting Display? Buttons on the DPC-7.4 Remote controllerCan’t view Jpeg files? Message no Play appears onComponent Video Specifications