Samsung HPN5039, HPN6339 Setting Up Your Remote Control, Changing Channels, Adjusting the Volume

Page 19

Changing Channels

Using the Channel Buttons

Press the CH or CH buttons to change channels.

When you press the CH or CH buttons, the PDP changes channels in sequence. You will see all the channels that the PDP has memorized. (The PDP must have memorized at least three channels.)

You will not see channels that were either erased or not memorized.

Directly Accessing Channels

Press the number buttons to go directly to a channel. For example, to select channel 27, press “2” then “7”. The TV will change channels when you press the second number.

When you use the number buttons, you can directly select channels that were either erased or not memorized. To change to single-digit channels (0~9) faster, press “0” before the single digit. (For channel “4” press “0”, then “4”.

Using the Pre-CH button to select the previous channel

Press the PRE-CH button. The TV will switch to the last channel viewed.

To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then, use the PRE-CH button to quickly alternate between them.

Adjusting the Volume

Using the Volume Buttons

Press the VOL + or VOL – buttons to increase or decrease the volume.

Using Mute

Using the MUTE Buttons

At any time, you can temporarily cut off the sound using the MUTE button.

Press the MUTE button and the sound cuts off.

1 The word “Mute” will appear in the lower-left corner of the screen.

To turn mute off, press the MUTE button again, or

2 simply press the VOL + or VOL – button.

36

Mute

Setting Up Your Remote Control

This PDP's remote control can operate almost any VCR, cable box or DVD. After it has been set up properly, your remote control can operate in four different modes :TV, VCR, Cable or DVD. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose.

Note : The remote control may not be compatible with all DVD Players, VCRs, Cable boxes.

The remote control can operate only on STB made by Samsung.

Setting Up the Remote to Operate Your VCR, Cable box or DVD player

1 Turn off your VCR. (or Cable box, DVD player)

Press the MODE button. Mode is changed whenever

2 MODE button is pressed(New mode is displayed on LED screen).

3 Press the SET button on your TV's remote control.

Using the number buttons on your remote control,

4 enter three digits of the VCR (or Cable box, DVD player) code listed on page 38 of this manual for your brand of VCR (or CATV, DVD). Make sure you enter three digits of the code, even if the first digit is a "0".

(If more than one code is listed, try the first one.)

Press the Power button on the remote control.

5 Your VCR (or CATV, DVD) should turn on if your remote is set up correctly. If your VCR (or CATV, DVD) does not turn on after setup, repeat steps

2, 3, and 4, but try one of the other codes listed for your brand of VCR (or CATV, DVD).

If no other codes are listed, try each code, 000 through 089 (or Cable box: 000 through 077, DVD player: 000 through 008).

Notes

When your remote control is in “VCR” mode, the VCR control buttons (Stop, REW, Play/Pause, FF) still operate your VCR.

When your remote control is in “CATV” or “DVD” mode, the VCR control buttons (Stop, REW, Play/Pause, FF) still operate your VCR.

37

Image 19
Contents Owner’s Instructions Thank You for Choosing Samsung Important Safety InformationUser Instructions FCC InformationUser Instructions Table of ContentsGeneral Information Your New Plasma Display Panel Remote Control Buttons Installation Notes Wall Installation InstructionsWall attachment panel PDP panel Wall How to Adjust Mounting AngleFactory default Changeing the angleConnections Cable without a Cable Box Connecting VHF and UHF AntennasConnecting Cable TV Antennas with 75-ohm Round LeadsCapability of 10 watts minimum impedance 8 ohm Connecting SpeakersViewing camcorder tapes Connecting a VCRConnecting a Camcorder Connecting a VCR to the Video or S-Video/Audio jackTo Watch DTV Playing DVDWatching DTV To Play DVDOperation Displaying Status Information Turning the PDP On and OffViewing the Menus and Displays Viewing the MenusMemorizing the Channels Selecting the Video Signal-sourceTo View Memorized Channel PIP Mode Changing Channels Setting Up Your Remote ControlAdjusting the Volume Using MutePicture Control Remote Control CodesVCR Codes Cable Box Codes DVD Codes Press the Menu button to exit Using Automatic Picture SettingsCustomizing the Picture Press the Menu button, then press the Enter ButtonDNIe Digital Natural Image engine Selecting the Color ToneSelecting the PIP Screen Viewing the Picture-in-PicturePress the UP or Down button to select Source Changing the Size of the PIP Window STD, HRD or IRC Changing the Location of the PIP ImageChanging the Screen Size Sound Control Customizing the Sound Using Automatic Sound Settings Press the Left or Right button to select Mono Stereo or SAP VolumeButton to select Sound, then press the Enter Press the UP or Down button to select AutoUsing a Subwoofer Using Dolby VirtualChannel Control LNA Low Noise Amplifier Fine Tuning ChannelsConnecting a PC and Operation To watch the PC screen Connecting to a PCPin Configuration Setting up Your PDP Plug and Play85.008 43.269 How to Set up Your PC Software Windows onlyColor Adjust will appear on the screen Adjusting the PC ScreenAdjusting the R.G.B Custom. When Custom is selected, the wordAppear Vertical, horizontal frequencies and resolutionChanging the Size of the Image Information Tion, then press the Enter buttonPicture Automatic Adjustment Picture Quality AdjustmentCoarse Adjustment Fine Tuning Fine Time SettingRemove picture noise on the screen by pressing Button to select Function, then press the Enter Setting the Clock Setting the Sleep TimerPress the UP or Down button to select Sleep Setting the On/Off Timer Setting the TimersFunction Description Setting the Preferred Channel and Volume LevelSelecting a Menu Language Viewing Closed Captions Power Off Setting Auto Power OffDigital Noise Reduction How to Enable/Disable the V-Chip Using the V-ChipHow to Set up Restrictions Using the TV guidelines Mpaa Rating Appendix Selecting the Film ModeTroubleshooting Care and Maintenance Specifications Memo