Samsung HPN6339, HPN5039 Connecting to a PC, Pin Configuration, Setting up Your PDP Plug and Play

Page 34

Connecting to a PC

Connection to a Macintosh computer may require in adapter.

PDP

Power Plug

Pin Configuration

D-Sub Cable

DVI-D Cable (Digital-Only Connector)

• 15Pin Signal Cable (based on protruded pin)

						or

Use the DVI-D
Use the DVI-D
connection cable.
(sold separately)
	DVI						PC			Cable
	DVI		Cable				PC			Cable

DVI jack

(The actual config- uration on your PC may be different, depending on the model.)

Connecting a PC to the PDP

Ferrite Cores(HPN5039)

Audio Cable

PC

Setting up Your PDP (Plug and Play)

Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual setup hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification data (EDID) using Display Data Channel (DDC) protocols.

1 Connect a PC (15pin) cable between the PC Output jack (or DVI jack) on the PC and the RGB IN(or DVI IN) Input jack (15p D-SUB) on the PDP.

2 Connect a Audio cable between the Audio (RGB or DVI) on the PC and the Audio L/R (RGB or DVI) input jacks on the PDP.

To watch the PC screen:

1.Turn on your PDP, and press the TV/VIDEO button on the remote control.

2.Press the UP or DOWN button to select “PC”, then press the ENTER button.

3.Turn on PC and check for PC system requirements. (Refer to pages 66 and 67 for PC system requirements.)

4.Adjust the PC screen. (Refer to pages 70 and 76.)

66

67

Image 34

Contents Owner’s Instructions Important Safety Information Thank You for Choosing SamsungFCC Information User InstructionsTable of Contents User InstructionsGeneral Information Your New Plasma Display Panel Remote Control Buttons Installation Notes Wall Installation InstructionsWall attachment panel Changeing the angle How to Adjust Mounting AngleFactory default PDP panel WallConnections Antennas with 75-ohm Round Leads Connecting VHF and UHF AntennasConnecting Cable TV Cable without a Cable BoxConnecting Speakers Capability of 10 watts minimum impedance 8 ohmConnecting a VCR to the Video or S-Video/Audio jack Connecting a VCRConnecting a Camcorder Viewing camcorder tapesTo Play DVD Playing DVDWatching DTV To Watch DTVOperation Viewing the Menus Turning the PDP On and OffViewing the Menus and Displays Displaying Status InformationSelecting the Video Signal-source Memorizing the ChannelsTo View Memorized Channel PIP Mode Using Mute Setting Up Your Remote ControlAdjusting the Volume Changing ChannelsPicture Control Remote Control CodesVCR Codes Cable Box Codes DVD Codes Press the Menu button, then press the Enter Button Using Automatic Picture SettingsCustomizing the Picture Press the Menu button to exitSelecting the Color Tone DNIe Digital Natural Image engineSelecting the PIP Screen Viewing the Picture-in-PicturePress the UP or Down button to select Source Changing the Size of the PIP Window Changing the Location of the PIP Image STD, HRD or IRCChanging the Screen Size Sound Control Customizing the Sound Using Automatic Sound Settings Press the UP or Down button to select Auto VolumeButton to select Sound, then press the Enter Press the Left or Right button to select Mono Stereo or SAPUsing Dolby Virtual Using a SubwooferChannel Control Fine Tuning Channels LNA Low Noise AmplifierConnecting a PC and Operation Setting up Your PDP Plug and Play Connecting to a PCPin Configuration To watch the PC screenHow to Set up Your PC Software Windows only 85.008 43.269Custom. When Custom is selected, the word Adjusting the PC ScreenAdjusting the R.G.B Color Adjust will appear on the screenTion, then press the Enter button Vertical, horizontal frequencies and resolutionChanging the Size of the Image Information AppearPicture Automatic Adjustment Picture Quality AdjustmentCoarse Adjustment Fine Tuning Fine Time SettingRemove picture noise on the screen by pressing Button to select Function, then press the Enter Setting the Clock Setting the Sleep TimerPress the UP or Down button to select Sleep Setting the Timers Setting the On/Off TimerSetting the Preferred Channel and Volume Level Function DescriptionSelecting a Menu Language Viewing Closed Captions Power Off Setting Auto Power OffDigital Noise Reduction Using the V-Chip How to Enable/Disable the V-ChipHow to Set up Restrictions Using the TV guidelines Mpaa Rating Selecting the Film Mode AppendixTroubleshooting Care and Maintenance Specifications Memo