FCC Information
•Protect the power cord. Power supply cords should be routed so that they won’t be walked on or pinched by objects placed on or against them. Pay particular attention to cords at plugs, convenience recepta- cles, and the point where they exit from the unit.
•Unplug the PDP from the wall outlet and disconnect the antenna or cable system during a lightning storm or when left unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and
•Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal.
•Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.
•Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. Never spill liquid of any kind on the PDP.
•Ground outdoor antennas. If an outside antenna or cable system is connected to the PDP, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built- up static charges. Section 810 of the National Electrical Code, ANSI/NFPA
•Do not attempt to service the PDP yourself. Refer all servicing to qualified service personnel. Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:
-when the
-if liquid has been spilled on the unit or if objects have fallen into the unit
-if the PDP has been exposed to rain or water
-if the PDP does not operate normally by following the operating instructions
-if the PDP has been dropped or the cabinet has been damaged
-when the PDP exhibits a distinct change in performance
•If you make adjustments yourself, adjust only those controls that are covered by the operating instruc- tions. Adjusting other controls may result in damage and will often require extensive work by a qualified technician to restore the PDP to normal.
•When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitu- tions may result in additional damage to the unit.
•Upon completion of any service or repairs to this PDP, ask the service technician to perform safety checks to determine that the PDP is in a safe operating condition.
•The PDP can properly operate in a temperature range of 32~104°F(0~40°C) and 80% humidity. Do not use in a hot and humid place.
•Before moving the PDP equipped with speakers, separate the speakers from the PDP. If you move the PDP with the speakers attached, it may result in damage or injury.
User Instructions
The Federal Communications Commission Radio Frequency Interference Statement includes the fol- lowing warning:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi- dential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar- antee that interference will not occur in a particu- lar installation .
If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter- ference by one or more of the following mea- sures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a cir- cuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
User Information
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. If necessary, consult your dealer or an experi- enced radio/television technician for additional suggestions. You may find the booklet called How to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal Communications Commission. It is available from the U.S. Government Printing Office, Washington, DC 20402, Stock Number
The party responsible for product compliance:
SAMSUNG ELECTRONICS CO., LTD America QA Lab of Samsung 3351 Michelson Drive,
Suite #290, Irvine, CA92612 USA
Warning
User must use shielded signal interface cables to maintain FCC compliance for the product. Provided with this monitor is a detachable power supply cord with IEC320 style terminations.
It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the volt- age rating of the computer convenience outlet is the same as the monitor and that the ampere rat- ing of the computer convenience outlet is equal to or exceeds the monitor voltage rating.
For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration
IC Compliance Notice
This Class B digital apparatus meets all require- ments of the Canadian
Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont
Notice de Conformité IC
Cet appareil numérique de classe B respecte toutes les exigences du Règlement
VCCI
This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interfer- ence. Install and use the equipment according to the instruction manual.
4 | 5 |