Toshiba 53AX62 owner manual Device code setup, Searching and sampling the code of a device, Recall

Page 16

Using the Remote Control

Programming the remote control for use with your audio/video devices

Device code setup

1.Refer to the Device code table on pages 18Ð21 to find the code for the brand of your device.

If more than one code is listed, try each one separately until you find the one that works.

2.Press MODE until the Mode indicator of the device (CABLE/SAT, VCR, DVD, AUDIO1, AUDIO2) lights up.

3.While holding down RECALL, press the Number buttons to enter the four-digit code for your device.

If the correct code is entered, the mode indicator will blink twice. If an incorrect code is entered, there will be one long blink.

4.Point the remote control at the device and press POWER to test the code.

If the device responds to the remote control, you have entered the correct code.

If the device does not respond, you may have entered the wrong code. Repeat steps 3 and 4 using another code.

5.To control the TV, press MODE to select TV.

Searching and sampling the code of a device (991)

If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that device mode, and sample various function buttons to find the code that enables the remote control to operate the target device. The keys available to be sampled, provided they are applicable to that mode, are 0, 1, 2, 3, POWER, VOL y, CH y, PLAY, and STOP. Invalid keys will be ignored while in program mode.

To cycle through each available device code and sample its functions:

1.Press MODE to select the mode you want to set up.

2.While holding down RECALL, press 9, 9, 1. The remote control will enter program mode.

3.Point the remote control at the target device, and then press POWER (or other function buttons that are available to be sampled).

4.If the device responds to the remote control:

Press RECALL to store the device code. The mode indicator will blink twice, and the remote control will exit program mode.

If the device does not respond to the remote control:

Press MENU y, and then press POWER. Repeat this step until the device responds to the remote control, and then press

RECALL.

Note: When the search cycle is done, the mode indicator will blink three times. The remote control will begin to cycle through the available codes again. If no key is pressed within 10 seconds while programming, the remote control will exit the program mode and return to the previous code.

POWER

Number

MODE

Menu y

RECALL

Note:

¥Each time you replace the batteries, you must reprogram the remote control.

¥Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled ÒVCR1/VCR2.Ó

If your VCR has this kind of switch and does not respond to any of the codes for your VCR brand, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 53AX62 Safety Precautions Dear CustomerImportant Safety Instructions InstallationService CareImportant Safety Information Introduction Exploring your new TV Welcome to ToshibaIntroduction Connecting your TV Connecting a VCRConnecting a cable converter box Connecting a cable converter box and a VCRYour You will need Three coaxial cablesConnecting a DVD player/satellite receiver and a VCR Introduction Connecting YourTV ControlUsing Remote Settingup YourTV TheTV’s Features UsingConnecting a DVD player with ColorStream component From Connecting two VCRsConnecting your TV Video and a VCRConnecting a camcorder Connecting an audio systemConnecting an A/V receiver Dolby Pro Logic* surround sound system Connection exampleInstalling the remote control batteries Preparing the remote control for useUsingtheTVÕs Features Appendix Using the Remote Control Remote control functional key chartDisc AM/FM Searching and sampling the code of a device Device code setupRecall Operational feature reset Using the Volume Lock featureVerifying the device code Cable box setup codes Device code tableVCR setup codes DVD setup codes CD Player setup codes Amplifier setup codes Learning about the remote control Introduction Connecting YourTV Learning about the menu systemChanging the on-screen display language Selecting the antenna inputUp TV Press x or to highlight your desired languageProgramming channels automatically Adding channels to the TV’s memoryPress y or z to select CH Program Changing channels Setting up your TVAdding and erasing channels manually Adjusting the color convergence Usingthe RemoteControlSettingup YourTV TheTV’s Features Adjusting, you must perform steps 8 and 9 twiceAdjusting the channel settings Switching between two channelsTV’s Features Programming your favorite channelsLabeling channels Connecting yourTVPress z to highlight Label Using the TV’s Features Repeat to enter the rest of the charactersSetting Your UsingtheTV’s Features Appendix Watching picture-in-picture PIPChanging the position of the PIP window Switching the main and PIP picturesFreezing the PIP picture Using the multi-window feature Using the multi-window channel preview functionUsing the multi-window favorite channel scan function Using the multi-window strobe functionUsing the Locks menu Press y or z to display the PIN code entering modeEntering the PIN code If you cannot remember your PIN codeUsing the V-CHIP menu Connecting YourTV ControlUsing Remote Setting YourTV UsingtheTV’s Features AppendixMpaa Rating Independent rating system for movies Blocking OptionTV None Rating Chip MenuUnlocking programs temporarily Locking channelsCH Lock Locking the video inputs Locking the front panel buttonsChanging the PIN code Front Panel LockAdjusting the picture Selecting the picture modeAdjusting the picture quality See ÒSaving your new picture preferencesÓ onUsing the flesh tone feature Using the noise reduction featureSaving your new picture preferences Noise ReductionSelecting the color temperature Resetting your picture adjustmentsSettingup YourTV UsingtheTV’s Features Appendix OFFWatching video input Selecting the video source labelsDTV SATUsing the closed caption feature Introduction Connecting YourTV Usingthe RemoteControlSettingup YourTV UsingtheTV’s Features ¥ To turn off the closed caption feature, highlight OFFSetting the clock Setting the sleep timerTo display the time on-screen Press Recall Muting the sound Adjusting the soundSelecting stereo/SAP broadcasts Using the surround sound feature Adjusting the sound quality Resetting your audio adjustmentsUsing the sub-bass system SBS Turning off the built-in speakersTo turn off the SBS Highlight OFF in above To turn on the built-in speakers Highlight on in aboveUsing the StableSound feature To turn off the StableSound feature Highlight OFF in aboveSelecting the Audio OUT sound MainSelecting the background of the menu display Viewing the demonstration modeDisplaying on-screen information Understanding the auto power off feature Understanding the last mode memory featureSpecifications AppendixTroubleshooting VIDEO1, VIDEO2, VIDEO3Limited United States Warranty Limited Canada Warranty Manufactured by
Top Page Image Contents