Panasonic DMP-BD85 Troubleshooting guide, General operation, Cannot eject disc

Page 32

Troubleshooting guide

Before requesting service, please perform the following steps.

Do you have the latest firmware installed?

Firmware updates may be released to correct operating irregularities that are discovered with certain movies. (> 14)

4

Make the following checks.

If the problem remains unresolved, consult your dealer for instructions.

The following do not indicate a problem with this unit:

Regular disc rotating sounds.

Image disturbance during search.

Unit doesn’t respond to remote control

or front panel buttons.

Press and hold [Í/I] on the main unit for 3 seconds.

If still unable to turn the unit off, disconnect the AC mains lead, wait 1 minute, then reconnect the AC mains lead.

Cannot eject disc.

The unit may have a problem.

1While the unit is off, press and hold [OK], the yellow button and the blue button on the remote control at the same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2Repeatedly press [1](right) on the remote control or [Í/I] on the unit until “06 FTO” is displayed on the unit's

display.

3Press [OK] on the remote control or [< OPEN/CLOSE] on the unit.

General operation

To return to the factory preset.

¾Select “Yes” in “Default Settings” in the Setup menu. (> 31)

To return all settings to the factory preset.

¾Reset the unit as follows:

1 While the unit is off, press and hold [OK], the yellow button and the blue button on the remote control at the

same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2Repeatedly press [1](right) on the remote control or [Í/I] on the unit until “08 FIN” is displayed on the unit's display.

3Press and hold [OK] on the remote control or [< OPEN/ CLOSE] on the unit for at least 3 seconds.

Power of this unit is turned off when the input for the TV is switched.

¾This is a normal phenomenon when using VIERA Link (HDAVI Control 4 or later). For details please read the operating instructions for the TV.

32

The remote control doesn’t work properly.

¾The remote control and main unit are using different codes. If “SET 1” , “SET 2” or “SET 3” is displayed when a button is pressed on the remote control, change the code on the remote control. (> 31)

¾It may be necessary to set the manufacturer code or the remote control code again after changing the batteries for remote control. (> 14)

The TV tuner mode is not displayed when the TV is switched on.

¾This phenomenon may occur, depending on the TV setting, when “Quick Start” is set to “On”.

Depending on the TV, this phenomenon may be prevented by reconnecting the HDMI cable to a different HDMI input terminal or by changing the HDMI auto connection setting.

You have forgotten your ratings password. You want to cancel the ratings level.

¾The ratings level returns to the factory preset.

1 While the unit is on, press and hold [OK], the yellow button and the blue button on the remote control at the same time for more than 5 seconds.

– “00 RET” is displayed on the unit’s display.

2Repeatedly press [1] (right) on the remote control or [Í/

I] on the unit until “03 VL” is displayed on the unit's display.

3Press [OK] on the remote control or [< OPEN/CLOSE] on the unit.

Picture

The images from this unit do not appear on the television.

Picture is distorted.

¾An incorrect resolution is selected in “Component Resolution” or “HDMI Video Format”. Reset the setting as follows:

1 While the unit is on, press and hold [OK], the yellow button and the blue button on the remote control at the same time for more than 5 seconds.

– "00 RET” is displayed on the unit’s display.

2Repeatedly press [1](right) on the remote control or [Í/I] on the unit until “04 PRG” is displayed on the unit's display.

3Press and hold [OK] on the remote control or [< OPEN/ CLOSE] on the unit for at least 3 seconds.

Set the item again. (> 30)

When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream, select “Yes” in “Default Settings” and make proper settings. (> 31)

¾The unit and television are using different video systems. While stopped, keep pressing [∫] and [< OPEN/CLOSE] on the main unit for 5 or more seconds. The system switches from PAL to NTSC or vice versa.

¾The system used on the disc doesn’t match your television.

PAL discs cannot be correctly viewed on an NTSC television.

This unit can convert NTSC signals to PAL60 for viewing on a PAL television (“NTSC Contents Output” in the “Picture”).

Video is not output.

¾Set the “High Clarity Sound” in the playback menu to “Off” to use the COMPONENT VIDEO OUT terminal or the VIDEO OUT terminal. (> 27)

VQT2H83

Image 32
Contents Operating Instructions Blu-ray Disc Player Model No. DMP-BD85Remove the connector cover For Saudi ArabiaForAustraliaandNewZealand ForAsiaandMiddleEastTable of contents Unit and media care AccessoryUsing the remote control Standby/on switch Í/I Control reference guideTurn the unit on and off TV operation buttonsType Logo Examples Playable contents Playable discs/Cards/USB devicesDiscs that cannot be played in this unit FinalizeBD-Video Region management informationStandard Quality Video Connecting to a TVHighest Quality Video Connecting to an amplifier/receiver Digital AudioAnalogue Audio      Cable connectionsWireless LAN Adaptor supplied Connecting to a broadband networkFollowing services can be used when this unit is ForAsia Connecting AC mains leadLead on page 2 Before Connection Setting Easy SettingNetwork Easy Setting Wired connectionAccess Point Connection Setting Network Easy Setting Connection TestNetwork Easy Setting Internet Connection Test Display Check the followingReprogramming the remote control Firmware updatingFor other Panasonic products For TV or amplifier/receiverTo switch drives Inserting or removing a mediaFunction menu BD/DVD/CDPlaying video contents Useful functions Press Option Select an item, then press OKWhat is BONUSVIEW? What is BD-Live?Press PIP To turn on/off secondary videoAbout Divx Video About Divx VIDEO-ON-DEMAND Regarding DivXDisplaying subtitles text Playing still pictures To show the picture propertiesInsert a disc, SD card or USB device Press 3, 4, 2, 1 to select the album and press OKPlaying music Playing a track in another folderInsert a disc or USB device Press 3, 4 to select the track and press OKEasy control only with Viera remote control Power on linkWhat is Viera Link Hdavi Control? Linked operations with the TVPress 3, 4, 2, 1 to select the item and press OK Enjoying Viera CastPress Viera Cast ≥ Press OK if the Control Panel is not displayed Dlna featureWhen connected to a Panasonic Dlna compatible recorder Diga Useful functions for when playing back pictures Press Option Select an item, then press OKStatus Show the picture properties Rotate Except for Slideshow Rotate the still picture Rotate LeftPlay Playback menuDisc Picture SoundSetup menu Display TV / Device Connection Network GeneralCannot eject disc Troubleshooting guideGeneral operation Audio PlaybackOn the unit’s display MessagesOn the television Hdmi AV OUT/DIGITAL Audio OUT Coaxial/Optical Audio InformationAbout audio from audio output terminal Bitstream Recommended audio output settingFor details of the each item, refer to About MP3/JPEG/DivX/ AVCHD/MPEG2 files DivXSubtitles text file of DivX MP3Structure of folders that can be played in this unit Specifications Supplemental information Glossary AvchdBD-J DTS-HDContact Information cdrequest@am-linux.jp Safety precautions Index IP address J Jpeg , 37 L LAN LanguageLocal storage M MPEG2 MP3 Network On-Screen Language Picture-in-picture Playback
Related manuals
Manual 44 pages 21.52 Kb