AMX FG147-04 manual Programming The MIO R-1 Audio, Using Connector Ports on The MIO R-1 Audio

Page 9

Programming The MIO R-1 AUDIO

Programming The MIO R-1 AUDIO

Most functionality of the MIO R-1 AUDIO is handled using the application KeypadBuilder. Go to www.amx.com for the KeypadBuilder Instruction Manual.

The MIO R-1 AUDIO recognizes a select number of Serial Commands. For a full list and descriptions, consult Persistent Serial Commands section on page 10.

Using Connector Ports on The MIO R-1 AUDIO

The programming jack is used for communication between the device and KeypadBuilder. The programming jack uses a three-wire, 2.5 mm stereo jack, you can order the programming cable (FG10- 817) from AMX if you do not currently possess one. While loading your configuration file make sure the device is situated as such that the batteries will not fall out. The load will fail if your batteries fall out during the process. The MIO communicates at 115200 baud rate.

To download KeypadBuilder Configuration Files:

1.Set the MIO R-1 AUDIO Download mode to ON. See the Configuration Mode section for details.

2.Flip and turn the MIO R-1 AUDIO AUDIO so that the buttons are facing away from you and the device is upside down.

3.Holding the device in both hands, place your thumbs on the battery door and push up to slide the battery door free.

4.Connect the 2.5 mm stereo plug (male) end of the programming cable (FG10-817) into the programming jack on the bottom side of the remote device.

5.If necessary, connect the DB-9 end of the programming cable to the female DB-9 connector on the DB-9 extension cable (FG10-727).

6.Connect the female DB-9 terminal end of the extension cable to the port on the back of your computer.

7.Configure the communication parameters in KeypadBuilder.

 

 

 

 

 

 

MIO R-1 AUDIO

Remote

 

 

 

 

Programming jack

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Stereo plug

 

 

 

DB-9

 

(male)

 

 

 

connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cable FG10-817 to cable FG10-727

FIG. 3 Connecting The MIO to Your PC

MIO R-1 AUDIO

5

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents MIO R-1 Audio AMX Limited Warranty and Disclaimer Table of Contents Direct Numeric Access Overview MIO R-1 Audio remote controllerTouch And Tilt Sensor SpecificationsMIO R-1 Audio Setup Installing Your Custom ButtonsInserting Batteries into the MIO R-1 Audio Battery Low Indicator Programming The MIO R-1 Audio Using Connector Ports on The MIO R-1 AudioIR Code Matrix IR Code MatrixIR Transmit Mode Configuration ModeTimeout Adjustment Download ModeDebug Mode Setting The IR FrequencyBattery Type LED Awake BrightnessClick Query for Devices Updating MIO R-1 Audio FirmwareSerial Commands Persistent Serial CommandsMIO-RCC Charging Base MIO Remote Charging BaseInstalling The Rechargeable Battery Charging The MIO Remote with Charging Base Rechargeable Battery Port on The MIO RemoteConfiguration Mode Changing Battery ModesUsing the MIO R-1 Audio Remote Tone Control & SRS SettingSRS WOW, Bass Boost, 3D and Focus Settings Zone Control Privacy ModeInternal Tuner and Audio Server Source ControlCD and DVD Satellite and OtherCustom XM Direct Numeric AccessTuners CD Player / ChangerCreating a Preset PresetsRecalling a Preset Clearing All PresetsZone Grouping Group Volume ControlAdding a Zone To a Group Grouping All ZonesCreating a favorite For a Specific Source FavoritesClearing favorite for a Specific Source and Specific Zone Clearing All Favorites for All Sources for specific ZoneSetting Alarm Time AlarmClearing Alarm For a Specific Zone Clearing Alarm For All ZonesLocking a Specific Keypad Keypad LockoutUnlocking a Specific Keypad Unlocking All KeypadsMIO R-1 Audio MIO R-1 Audio It’s Your World Take Control
Top Page Image Contents