Universal Electronics ATLAS OCAP Clearing Custom Programming, To Re-Assign Perform Key Sequence

Page 24

Atlas OCAP M1056L.fm Page 24 Friday, December 22, 2006 6:10 PM

3.Press AUD once, then press VCR once. The VCR

key will blink twice.

The VCR key is now ready to be programmed for your second audio device. See “Programming Device Control” on page 10. To re-assign other device keys, repeat these and substitute the key sequence using the following chart:

NOTE: Only one device can be assigned to an unused device key at a time.

To Re-Assign

Perform Key Sequence

 

 

VCR as 2nd VCRÆSETUPÆ9Æ9Æ2ÆAUDÆVCR AUD key

VCR as 2nd VCRÆSETUPÆ9Æ9Æ2ÆTVÆVCR TV key

VCR as 2nd VCRÆSETUPÆ9Æ9Æ2ÆCBLÆVCR CBL key

VCR back to VCRÆSETUPÆ9Æ9Æ2ÆVCRÆVCR VCR

To re-assign another unused device key, substitute it for the VCR key above and then perform the sequence. For example, to re-assign an unused AUD key as a second DVD key, perform

AUDÆSETUPÆ9Æ9Æ2ÆDVDÆAUD.

When a re-assignment is done, the selected device key (e.g., AUD) will blink twice to confirm your choice. At that time, you will need to program device control (see “Programming Device Control” on page 10).

CLEARING CUSTOM PROGRAMMING

The Atlas OCAP 5-Device Remote Control with Learning contains a Custom Programming Reset program. You can use it to remove all custom programming, except your setup codes and reassigned device keys.

IMPORTANT: Executing this program will erase all cus- tom settings for Volume Lock, Learned Keys, Tune-In Keys, and Channel Lock. However, your device programming remains.

1.On the remote control, press and hold SETUP

until the last-selected device key blinks twice.

www.urcsupport.com/atlasocap

24

Image 24
Contents Preprogrammed for Your SET-TOP BOX Table of Contents Atlas Ocap M1056L.fm Page 3 Friday, December 22, 2006 610 PM Introduction Features and Functions Key Charts KeyFunctionUse VOL+ or VOL- to raise or lower the audio volume Device Table Device KeyInstalling Batteries On the remote control, press a device key once Programming Device ControlSetting UP a Combo Unit Searching for Your Code Page Using Learning Learning PrecautionsChecking the Codes Programming a Learned Key Deleting a Single Learning Key TV, or CBLProgramming Channel Control Lock Unlocking Channel ControlChanging Volume Lock Locking Channel Control to CBLLocking Volume Control To One Mode Global Volume Lock Programming Cable ID Lock Programming Macro KeysProgramming a Macro Key Clearing a Macro KeyUsing the Master Power KEY Programming the Master Power KeyUsing the Master Power Key Clearing the Master Power KeyRE-ASSIGNING Device Keys Clearing Custom Programming To Re-Assign Perform Key SequenceTroubleshooting Activating Backlighting OptionalFCC Notice Additional Information Setup Codes for Audio Amplifiers Setup Codes for Audio ReceiversMANUFACTURER’S Codes AMW JBL KLHLXI MCS1023, 1609, 1254 Setup Codes for Audio Accessories Setup Codes for Cable Boxes/ConvertersSSI ABC1256 Setup Codes for Cable/DVR/PVR Combos Setup Codes for DVD PlayersBBK CavsESA GPX JSI0591, 0692 SVA Page Setup Codes for DVD Recorders Setup Codes for DVD Combos LCDGOI HTSUsdtv ABSSetup Codes for DVR/PVR Systems AOC CCECXC Page JCB KECKMC KTVMTC NTC1447, 0047, 1958 SSS TMK TVSSetup Codes for TVs Hdtv 0047 Setup Codes for TVs Plasma Setup Codes for TV/DVD Combos Hitachi 1247 ILo 1472 Initial Jensen 1016 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos Setup Codes for VCRs HI-Q Keen 0693 Kenwood 0067, 0041, 0038 0060, 0240, 0042 STS Setup Codes for Video Accessories DDIDvico Setup Codes for Video Accessories Hdtv SMCPage Page M1056L Revision