Universal Electronics ATLAS OCAP manual Activating Backlighting Optional, Troubleshooting

Page 25

Atlas OCAP M1056L.fm Page 25 Friday, December 22, 2006 6:10 PM

2.Enter 9 8 0. The last-selected device key

blinks twice, pauses, and blinks twice again to confirm that all custom programming is cleared.

ACTIVATING BACKLIGHTING (OPTIONAL)

On some models of your Atlas OCAP 5-Device Remote Control with Learning, you can activate backlighting. Backlighting enables your remote’s keypad to remain lit for five seconds after you press any key. To enable backlighting on a remote with that feature, perform the following step:

1.Press SETUP twice within one second.

Backlighting is turned on.

To disable backlighting, perform the following step:

1.Press SETUP twice within one second.

Backlighting is turned off.

TROUBLESHOOTING

PROBLEM: Device key does not blink when you press a key.

SOLUTION: Replace the batteries with two (2) new AA batteries (see “Installing Batteries” on page 9).

PROBLEM: Device key blinks when you press a key, but home entertainment device does not respond.

SOLUTION: Make sure you are aiming the remote control at your home entertainment device and that you are within 15 feet of the device you are trying to control.

PROBLEM: The remote control does not control home entertainment devices or commands are not performing properly.

SOLUTION: Try all listed codes for the device brand being set up. Make sure all devices can be operated with an infrared remote control.

PROBLEM: TV/VCR Combo does not respond properly.

SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation (see page 11).

PROBLEM: No volume on a second TV.

SOLUTION: Follow instructions under “Changing Volume Lock” on page 18.

www.urcsupport.com/atlasocap

25

Image 25
Contents Preprogrammed for Your SET-TOP BOX Table of Contents Atlas Ocap M1056L.fm Page 3 Friday, December 22, 2006 610 PM Introduction Features and Functions KeyFunction Key ChartsUse VOL+ or VOL- to raise or lower the audio volume Device Key Device TableInstalling Batteries Programming Device Control On the remote control, press a device key onceSetting UP a Combo Unit Searching for Your Code Page Learning Precautions Using LearningChecking the Codes Programming a Learned Key TV, or CBL Deleting a Single Learning KeyUnlocking Channel Control Programming Channel Control LockLocking Channel Control to CBL Changing Volume LockLocking Volume Control To One Mode Global Volume Lock Programming Macro Keys Programming Cable ID LockClearing a Macro Key Programming a Macro KeyProgramming the Master Power Key Using the Master Power KEYClearing the Master Power Key Using the Master Power KeyRE-ASSIGNING Device Keys To Re-Assign Perform Key Sequence Clearing Custom ProgrammingActivating Backlighting Optional TroubleshootingFCC Notice Additional Information Setup Codes for Audio Receivers Setup Codes for Audio AmplifiersMANUFACTURER’S Codes AMW KLH JBLLXI MCS1023, 1609, 1254 Setup Codes for Cable Boxes/Converters Setup Codes for Audio AccessoriesSSI ABC1256 Setup Codes for DVD Players Setup Codes for Cable/DVR/PVR CombosCavs BBKESA JSI GPX0591, 0692 SVA Page Setup Codes for DVD Combos LCD Setup Codes for DVD RecordersHTS GOIABS UsdtvSetup Codes for DVR/PVR Systems CCE AOCCXC Page KEC JCBKMC KTVNTC MTC1447, 0047, 1958 SSS TVS TMKSetup Codes for TVs Hdtv 0047 Setup Codes for TVs Plasma Setup Codes for TV/DVD Combos Hitachi 1247 ILo 1472 Initial Jensen 1016 Setup Codes for TV/VCR Combos Setup Codes for TV/VCR/DVD Combos Setup Codes for VCRs HI-Q Keen 0693 Kenwood 0067, 0041, 0038 0060, 0240, 0042 STS DDI Setup Codes for Video AccessoriesDvico SMC Setup Codes for Video Accessories HdtvPage Page M1056L Revision