Mitsubishi Electronics WD-52527 manual Hdtv Cable Box or Satellite Receiver with Component Video

Connecting a DVD Player with Component Video Connecting an HDTV Cable Box or Satellite Receiver with Component Video

DVD Player with Component Video

Figure 9

Component video cables and audio cables are required. These are not included with the TV.

1.Connect the Component Video cables from Y/Pr/ Pb VIDEO OUT on the back of the DVD player to COMPONENT-2 on the TV back panel, matching the correct connection:

•Y to Y (Green)

•Pr to Pr (Red)

•Pb to Pb (Blue)

2.Connect a set of audio cables from AUDIO OUT on the back of the DVD player to COMPONENT-2 AUDIO Input on the TV back panel. The red cable connects to the R (right) channel, and the white cable connects to the L (left) channel.

57
CBDL
QBOFM
TFDUJPO

5P 57 $PNQPOFOU 				COMPONENT
: 13 1C JOQVUT			YPbPr (480i/480p/720p/1080i)
			1	2	3
						Y
						Pb
8IJUF						Pr
						LEFT/
						AUDIO-
						(MONO)
						AUDIO-
		3FE				RIGHT

%7%
CBDL
QBOFM



:

7*%&0

"6%*0 065

.*546#*4)*

"$ */

 $) 463306/%

$)

#*5453&".1$.

$&/5&3

%7% 1-":&3

8IJUF

$#

4

-

$3

46#800'&3 463306/% '30/5

3

$0"9*"-

3FE



7*%&0 065

HDTV Cable Box or Satellite Receiver with Component Video

Figure 10

A coaxial splitter, RCA component video cables, and audio cables are required. These are not included with the TV.

1.Connect the outside antenna, cable, or satellite to ANT or SATELLITE IN on the cable box or satellite receiver. See your device’s owner’s guide for instructions and cable compatibility.

2.Connect the incoming terrestrial antenna or cable (not satellite) to ANT-1 on the TV back panel (a coaxial splitter, available at most electronic supply stores, may be required to complete this installation).

3.Connect RCA-type cables from the YPrPb outputs on the DTV receiver to Component-1 on the TV back panel, matching the correct connections:

DTV Receiver to TV Back panel

•Y to Y

•Pr to Pr

•Pb to Pb

4.Connect L (left) and R (right) audio cables from the DTV receiver to Component-1 AUDIO on the TV back panel.

5.If you are using a cable-box input other than Component-1 (the default), open the NetCommand RF Connection for Cable screen (see page 49) or the Connection for [device] screen (see page 48) to change the input.

Note: To use the benefits of a digital A/V receiver, connect your cable box or satellite receiver’s digital audio out to a digital input on your digital A/V receiver.

Figure 9. Connecting a DVD Player with Component Video

Note: NetCommand® will assume you connected your DVD player to Component-2. If you add a second DVD or use any other inputs for your DVD, this change must match in the NetCommand system. See Edit NetCommand...

in Chapter 3 for more information.

IMPORTANT

See Appendix B for component video signal compatibility information.

For digital audio connections to your A/V receiver , see your HDTV Receiver and A/V

%57
3FDFJWFS
XJUI
:1S1C
DPOOFDUJPOT



:

"6%*0

"6%*0

8IJUF



-

-

7$3

$0/530-

1C

3

3

3'

3FE

%*(*5"-

"6%*0 065

1S

7*%&0

7*%&0

1)0/& +"$,

3&.05&

47*%&0

57 CBDL QBOFM TFDUJPO



COMPONENT

INPUT

YPbPr (480i/480p/720p/1080i)

3

1

2

1

2

Y

S-VIDEO

Pb

Pr

VIDEO

AUDIO-

AUDIO-

LEFT/

LEFT/

(MONO)

(MONO)



AUDIO-

AUDIO-

RIGHT

RIGHT

',INK¸

IR EMITTER

Net Command¸



	DTV/CABLE/
	VHF/UHF
	USE WITH
*ODPNJOH "OUFOOB 		ANT 1 / MAIN	ANT 2 / AUX
PS $BCMF	CableCARD

$"65*0/ 3*4,
0'
&-&$53*$"-
4)0$, %0
/05
01&/

065
50
57

$)
 $)


*/
'30.
"/54"5&--*5&
*/

PS



					UP	BOUFOOB
		INPUT		OUTPUT
			DVI	DBCM		F PS TBUFMMJUF
				AUDIO	RECORD
Analog Audio				OUTPUT	OUTPUT
1	2

VIDEO

AUDIO-

LEFT/

(MONO)

AUDIO-

RIGHT



receiver Owner’s Guides.

Figure 10. Connecting an HDTV cable box or Satellite Receiver with Component Video Connections

Chapter 2. Connecting 29