Mitsubishi Electronics WD-52527 manual Connecting the IR Emitter NetCommand

Page 31

Connecting the IR Emitter NetCommand®

IR Emitter NetCommand®

Figure 13

A double IR Emitter cable is included with models WD-52527 and WD-62527. A Quadruple IR Emitter cable is included with models WD-52528 and WD-62528.

The emitters connected to these jacks are used by the NetCommand system to control other devices such as VCRs, DVD players, Cable boxes and Satellite receivers.

1.Connect the plug end of the supplied IR Emitter Cable to either one of the IR Output NetCommand jacks on the TV back panel.

2.Run the cable for each of the emitter ends under, along side or over the top of each device to be controlled to the area of the front where the remote control sensor is located.

3.Place the emitter end in front of the remote control sensor of the device to be controlled. The emitter bulb should face the remote control sensor. This bulb emits infrared light in a cone shaped pattern. The bulb needs to be placed far enough from the remote control sensor to allow the cone pattern to include the sensor.

The remote control sensor is usually behind the plastic window of the front display panel. It is sometimes visible when you look through the display plastic using a flashlight and is normally a round or square cutout

behind the plastic. If you cannot see the sensor and the device’s Owner’s Guide does not specify the location, you can find it by using the device’s remote control. Hold the remote about 1/2 inch from the front of the device. Starting from one end of the display window plastic, press the POWER button.

If the device does not respond, move the remote control 1 inch toward the center and try again. Repeat this until the device responds. Note this location then start over from the other end of the display window plastic, repeating until the device responds again. The remote control sensor will be somewhere between these two positions. This is usually enough accuracy for the placement of the IR emitters.

With some devices, the emitter will work better facing downward from the top of the device. Some experimentation may be needed.

The emitter end being used can be secured in place using double stick tape.

If you are not going to be using all emitter ends, place the unused ends behind the devices so that they cannot send signals to the remote control sensors.





0UIFS"7EFWJDF

4

$)



 "73FDFJWFS

Figure 13. Connecting IR Emitter NetCommand

57CBDLQBOFMTFDUJPO



',INK¸

 

IR EMITTER

Net Command¸

0UIFS"7EFWJDF

IMPORTANT

If a single emitter end can be placed in a position that will operate more than one device, do not use a separate emitter end for the additional device. A single device receiving remote control signals from too many emitters or remote controls may not respond at all.

Chapter 2. Connecting 31

Image 31
Contents Owner’s Guide Risk of Electric Shock Do not Open While Under Warranty After WarrantyPage Important Safeguards Important Safeguards Contents Ieee 1394 Devices and NetCommand Controlled Recordings Mitsubishi Digital Electronics America, Inc Our ThanksChapter Special Features TV AccessoriesWidescreen Picture Format Special FeaturesNetCommand Home Network Control System Digital Cable Ready CableCARD      TV AccessoriesOverview Remote Control Functions OverviewConnect WD-52528, WD-62528 Initiates Ieee Installing the Batteries Remote Control Functions OperationFor Best Results from the Remote Control Remote Control Functions Care and Sleep TimerSetting the Sleep Timer Canceling the Sleep TimerInput System ResetReset Front Control PanelLamp Indicator Front-Panel Indicator LightsIndicators Power/Timer IndicatorStatus Indicator WD-52527 WS-62527 Back PanelDVI Analog Audio Service PortWD-52528 WD-62528 Output Audio Output, Record OutputCableCARD Slot DTV Link/IEEEDigital Audio Output DVD Player with Component Video ConnectingChart Connecting External Devices and NetCommand SetupWall Outlet Cable Connecting a Wall Outlet Cable or Cable BoxStandard Cable Box CableCARD Technology Using a CableCARDFor cable or antenna with coaxial lead For antennas with flat twin leadsConnecting a VCR to an Antenna or Wall Outlet Cable UUBDIPOMZPOFDBCMFUZQF Connecting VCR Video and Audio to a Cable BoxSatellite Receiver or Other Device with S-Video Receiver Stereo SystemTo connect an analog A/V receiver Receiver Owner’s Guides Hdtv Cable Box or Satellite Receiver with Component VideoHdmi Device Connecting an Hdmi or DVI DeviceConnecting IR Emitter NetCommand Connecting the IR Emitter NetCommandDigital Control Signal Connecting Compatible Ieee 1394 DevicesDigital Video Signals Digital Audio SignalsHub Connection Style Pin Style vs -Pin Style ConnectorsConnection Styles Direct Device-To-Device StyleConnecting Helpful Hints NetCommand Setup and Editing Welcome To NetCommand NetCommand IntroductionNetCommand Pre-Memorized Devices Using the Remote Control with NetCommandNetCommand Setup On-Screen Buttons 3D Graphical Menu System Remote Control ButtonsNetCommand Information Screen NetCommand Initial SetupWelcome Screen TV Guide On Screen System Setup Device Setup ScreenReview screen Review ScreenReceiver Screen Edit NetCommand, Add an A/V ReceiverReceiver Inputs Receiver AVR Learn Screen Receiver AVR Input Learn ScreenAudio Output to AVR Screen Name ScreenEdit NetCommand Screen Edit NetCommand, Add DevicesAdd Screen Device Screen Edit NetCommand Add DevicesDevice Learn Screen Connection for Device Screen Device Advanced Learn ScreenRF Connection for Cable Screen VCR for Recordings ScreenIR Code for Device Screen Change Device Screen Edit NetCommand, Change or Delete Devices, Finish ScreenDelete Device Screen Disc Search Track List Screen Device Selection MenuIeee 1394 Devices and NetCommand Control New 1394 Device Screen Adding Ieee 1394 Devices AutomaticallyAdding Ieee 1394 Devices Automatically Name for 1394 Device ScreenConnection Screen Ieee 1394 Device Type ScreenPIP Device Selection Menu Device Selection MenuCableCARD Menu Using the Device Menu Button to Display MenusDevice Menu IR Controlled DevicesDevices 1394 or IR Controlled Using the Guide Button to Display ChannelView and MenusRecording Setup Guide ButtonCanceling a Current Peer-to-Peer Connection NetCommand Controlled Peer-to-Peer ConnectionsWhat is a Peer-to-Peer Connection? Setting up a Peer-to-Peer ConnectionDisc Search Direct VCR Recording from an Antenna or Cable SourceRestrictions for Traditional VCRs Page TV Menu Screen Operations Main Menu Choices Main menu, Setup selectedMemorize Channels Setup MenuLanguage ClockChannel Timer On/OffAuto DeviceIcon Order NetCommand MenuRemote Control Transport Buttons EditRecording Now Time-Delayed RecordingRecord Menu RecordRecord List Default Digital Record DeviceSetting Up Analog Recordings with TV Guide On Screen Cancel Current RecordingsMemory Channel MenuAntenna Prefer DigitalSQV SuperQuickView Signal StrengthSQV SuperQuickView Captions Menu Analog and Digital Captions Captions Menu, Customizing Digital Settings Chip Start Time and V-Chip Stop Time Chip Lock Menu Pass CodeChip EntryTV Ratings Chip Signal InformationContent Categories Chip Lock Menu V-Chip DefinitionsLock By Time Chip Lock MenuFront Button Lock Audio/Video Menu Analog-Only Audio Settings Setting Descriptions AudioAnalog and Digital Audio Setting Digital-Only Audio SettingsVideo Settings Setting Descriptions VideoPIP/POP off Operation of PIP and POPIndex TV Display Formats Device Control with NetCommandAppendix B Specifications WarrantyTV Display Formats Signal and Format DefinitionsDVD Definitions 57%JTQMBZ Digits Device Control with Net CommandCH up/down VOL up/downIeee 1394 Devices Special Features Bypassing the V-Chip Lock Appendix a Bypassing the V-Chip LockBypassing Front Button Lock This page intentionally blank TV Specifications Appendix B SpecificationsAppendix B Specifications Programming the Remote to Control NetCommand A/V Products Appendix C Remote Control Programming CodesDVD Players Mitsubishi CD Players Not all functions for all models Cable Boxes and Satellite ReceiversReceivers Mitsubishi A/V ReceiversAppendix D On-Screen Information Displays Check BOX Name Remote Appendix E NetCommand Specialized Device KeysAppendix F Cleaning and Service Cleaning the Dust Filter Appendix G Filter CleaningLamp Life Appendix H Lamp Cartridge Replacement3FQMBDJOHUIF-BNQ$BSUSJEHF Problem Possible Solution TroubleshootingTroubleshooting Troubleshooting Troubleshooting MENU, 0, QV Demo Mode103 Trademark and License Information104 Index105 106 Mitsubishi TV Software107 Mitsubishi LCD Rear Projection Television Limited Warranty108 Mitsubishi LCD Rear Projection Television Limited WarrantyPage Website Mail MDEAservice@mdea.com
Related manuals
Manual 71 pages 26.25 Kb Manual 71 pages 21.97 Kb Manual 69 pages 19 Kb