Mitsubishi Electronics WD-73727, WD-52628, WD-62628 Status Indicator, Power/Timer Indicator, Reset

Page 13

Front Control Panel, continued

Status Indicator

Indicator Color

TV Condition

Additional Information

 

 

 

None (indicator off)

Normal TV on or standby condition.

Normal operation.

 

 

 

Yellow, steady

Room temperature is too high.

TV will not operate when the ambient room

 

 

temperature is too high. Turn off the TV and wait

 

 

until the room temperature drops.

 

 

 

Red, either steady or

TV may require service.

Turn off the TV and unplug the set from the AC power

blinking

 

source. Wait one minute and then plug the set back

 

 

in.

 

 

If the LED is still on, contact your dealer or a

 

 

Mitsubishi Authorized Service Center. See

 

 

www.mitsubishi-tv.com or call 1-800-332-2119 to

 

 

receive Authorized Service Center information.

Power/Timer Indicator

Indicator Color

TV Condition

Additional Information

 

 

 

None (indicator off)

TV is powered OFF.

Normal operation.

 

 

 

Green, steady

TV is powered ON.

Normal operation.

 

 

 

 

Green, rapid blinking

1.

TV just plugged into AC outlet.

Wait until blinking stops before turning on

 

 

 

(approximately 1 minute). Normal operation.

 

2.

AC just restored after power

Wait until blinking stops before turning on

 

 

failure.

(approximately 1 minute). Normal operation.

 

 

 

 

 

3.

TV Rebooting after System Reset

Wait until blinking stops before turning on

 

 

used.

(approximately 1-2 minutes). Normal operation.

 

 

 

 

 

4.

TV Rebooting after power

Wait until blinking stops before turning on

 

 

fluctuation or receiving abnormal

(approximately 1 minute). Normal operation.

 

 

digital signals from digital channel,

 

 

 

CableCARD™, or digital device.

 

 

 

 

 

 

5.

You have begun the procedure

For detailed information, see the instructions

 

 

to update software from an

that accompany the authorized software update.

 

 

authorized flash memory device.

Important: Do not use non-authorized software at

 

 

 

any time.

 

 

 

Green, slow blinking

TV powered off and automatic-on

Normal operation. TV can be turned on at any time.

 

timer is set.

 

 

 

 

 

A/V Reset

There may be times when you wish to reset the A/V (Audio and Video) settings back to the factory defaults. To return all the settings at once, press GUIDE and FORMAT on the front panel at the same time. To reset the defaults for individual devices, use the A/V Memory Reset selection on the Audio/Video menu.

Chapter 1. Television Overview

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents TV Information Visit our website atStand Requirement TV Guide On Screen Access RequirementsFCC Declaration of Conformity Important Safeguards Important Safeguards Contents Mitsubishi DLP Projection Television Limited Warranty Mitsubishi Digital Electronics America, Inc Our ThanksTV Accessories Special Features Front Control Panel Remote Control      TV AccessoriesSpecial Features Front Control Panel Front-Panel Indicator Lights Lamp IndicatorModels WD-52628, WD-62628 Model WD-73727Power/Timer Indicator Status IndicatorReset Overview Remote ControlSleep Timer Battery InstallationCare TV Back Panel IR Emitter NetCommandComponent 1, 2, and 3 Inputs Input 1DTV Link/IEEE Hdmi 1CableCARD Slot Digital Audio OutputCard Compatibility Memory Card Reader and Front-Panel InputsMemory Card Input 3 and Ieee Reader Input/Output Input 3 and Ieee 1394 Input/OutputTV Reset Menu System Reset ButtonDemo Mode Additional InformationConnecting Stereo and/or digital audio cables AV Receiver Connecting External Devices and NetCommand SetupUsing a CableCARD Using a CableCARDCableCARD Technology Wall Outlet Cable Connecting a Wall Outlet Cable or Cable BoxStandard Cable Box Can be used with a CableCARDAntennas with Separate UHF and VHF Leads Antenna with a Single LeadFor antennas with flat twin leads For cable or antenna with coaxial lead$BCMF VCR to an Antenna or Wall Outlet Cable Audio & VideoVCR to a Cable Box Audio & Video Connecting a VCR to a Cable Box Audio & VideoSatellite Receiver or Other Device with S-Video Receiver Stereo SystemTo connect an analog A/V receiver DVI Device DVD Player with Component VideoHdmi Device Hdtv Cable Box or Satellite Receiver with Component VideoComputer with an Hdmi Monitor Output Connecting a Computer with an Hdmi or DVI Monitor OutputComputer with a DVI Monitor Output To view PC video on the TVConnecting IR Emitter NetCommand Connecting the IR Emitter NetCommandWhen Connecting Ieee 1394 Devices Connecting Compatible Ieee 1394 DevicesCompatible Ieee 1394 Devices Connection Styles Pin-Style vs -Pin-Style ConnectorsDirect Device-To-Device Style Hub Connection StyleHelpful Hints for NetCommand Connections Page NetCommand Setup and Editing NetCommand Introduction NetCommand Pre-Memorized Devices Using the Remote Control with NetCommandReceiver Cable Box SAT Satellite DVD Player ReceiverNetCommand Setup On-Screen Buttons 3D Graphical Menu System Remote Control ButtonsNetCommand Information Screen NetCommand Initial SetupSetup Reminder Welcome ScreenTV Guide On Screen System Setup Device Setup ScreenFinish Screen Review ScreenReceiver Screen Edit NetCommand Add an A/V ReceiverReceiver Inputs Receiver AVR Learn Screen Receiver AVR Input Learn ScreenAudio Output to AVR Screen Name ScreenEdit NetCommand Screen Edit NetCommand Add DevicesAdd Screen Device Learn Screen Device ScreenConnection for Device Screen Device Advanced Learn ScreenRF Connection for Cable Screen VCR for Recordings ScreenIR Code for Device Screen Change Device Screen Edit NetCommand Change or Delete DevicesDelete Device Screen Ieee 1394 Devices and NetCommand Control Adding Ieee 1394 Devices Automatically Adding Ieee 1394 Devices AutomaticallyNew 1394 Device Screen Name for 1394 Device ScreenConnection Screen Ieee 1394 Device Type ScreenPage NetCommand Functions PIP Device Selection Menu Device Selection MenuDevice Menu Using the Device Menu Button to Display MenusCableCARD Menu IR Controlled DevicesGuide Button Using the Guide Button to Display ChannelView and MenusGuide and the Device Selection Menu Guide and the Record To MenuNetCommand-Controlled Recordings Restrictions for Traditional VCRs Copy-Protected MaterialSetting up a Non-Recording Peer-to- Peer Connection What is a Peer-to-Peer Connection?Cancelling a Peer-to-Peer Connection Peer-to-Peer ConnectionsDisc Search Using A/V DiscsTrack List Screen TV Menu Operations Main Menu Language Setup MenuMemorize Channels ClockLamp Reminder TimerSoftware Version Remote Control Transport Buttons NetCommand MenuEdit Icon OrderTime-Delayed Recording Recording SetupRecord Menu RecordSetting Up Analog Recordings with TV Guide On Screen Default Digital Record DeviceTV Guide On Screen and the Record List Analog RecordingsChannel Menu SQV SuperQuickView Signal StrengthCaptions Menu Digital SettingsAnalog Captions BackgroundSize FontsColor Opacity FontSetting V-Chip Options Setting a Pass CodeChip Lock Menu Chip Lock Menu OverviewLock by Time V-CHIP ButtonFront Button Lock Bypassing V‑Chip Lock and Lock by TimeContent Categories Chip Signal InformationPrograms without V-Chip signals Chip RatingsAudio/Video Menu Analog and Digital Audio Settings Audio SettingsAnalog-Only Audio Settings Digital-Only Audio SettingsVideo Settings Video SettingsPC Video Settings Page MediaCommand and Memory Card Playback Additional FeaturesMemory Card Slots MediaCommand and Memory Card PlaybackMedia Command and Memory Card Playback Operation of PIP and POP TV Display Formats Signal DefinitionsDVD Definitions Format Definitions57%JTQMBZ PC Viewing PC resolution XGA selectionSignal Format Standard Zoom Signal Format 16 X 9 StandardPC Display Formats Troubleshooting General TV Operation Symptom Suggested SolutionTroubleshooting Position PictureSound IndicatorsDevice Ieee 1394 DevicesTV Guide On Screen Page Appendix G Cleaning and Service Appendix a SpecificationsTV Specifications Appendix a SpecificationsInputs Outputs Analog Program Appendix B On-Screen Information DisplaysDigital Program Digital Ieee 1394 DeviceBypassing the V-Chip Lock Appendix C Bypassing the V-Chip LockDeactivating the Front Button Lock This page intentionally blank Programming the Remote to Control NetCommand A/V Products Appendix D Remote Control Programming CodesReceivers Cable BoxesSatellite Receivers/SAT/DTV DVD PlayersVCRs Cable/SAT/DTV position TV positionVCR position DVD positionNetCommand Compatible Traditional Devices Analog Appendix E Device Control with NetCommandWhen an Ieee 1394 Device is Viewed or Played Appendix F NetCommand Specialized Device Keys Appendix G Cleaning and Service Do not touch the glass parts of the lamp cartridge Appendix H Lamp Cartridge ReplacementWash Your Hands THOROUGHLY, AS this Lamp Contains Mercury Source device Appendix I Recording and Viewing CombinationsDigital VCR or A/V Disc Connected to IEEE-1394 Port Trademark and License Information Mitsubishi TV Software 118 Mitsubishi DLP Projection Television Limited Warranty119 This Limited Warranty does not CoverIndex IndexIndex Page Page Website Mail MDEAservice@mdea.com
Related manuals
Manual 86 pages 7.9 Kb
Top Page Image Contents