Mitsubishi Electronics HC1100 user manual Viewing video images, Plugging in the power cord

Page 14
Audio cable (Option)

Viewing video images (continued)

Connecting to video equipment having a DVI-D terminal

You can project high-quality images by connecting the DVI-D terminal of this projector to video equipment having a DVI-D output terminal. In addition, this projector supports HDCP and is able to receive encrypted digital video data that are output from DVD players.

Equipment having a DVI-D terminal

To audio output

To audio input

terminals

terminals

To DVI-D terminal

DVI cable (Option)

To DVI-D (HDCP) terminal

For connection to the DVI-D terminal, use a commercially available DVI cable.

Select DVI as the input source.

Only RGB signals are supported. Component video signals are not supported.

HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital video data for the purpose of copy protection.

This projector uses stereo mini plug for its audio input.

When DVI is selected as the input source, setting of COLOR, TINT, FINE SYNC., TRACKING and HOLD is unavailable.

When you connect this projector and a DVI-Digital device (such as a DVD player) via the DVI terminal, black color may appear light and pale, depending on the type of the connected device.

This depends on the black level setting of the connected device. There are two kinds of methods to digitally transfer image data, in which different black level settings are employed respectively. Therefore, the specifica- tions of the signals output from DVD players differ, depending on the type of the digital data transfer method they use.

Some DVD players are provided with a function to switch the methods to output DVI-Digital signals. When your DVD player is provided with such function, set it as follows.

NORMAL EXPAND or ENHANCED

See the users guide of your DVD player for details.

When your DVD player does not have such function, adjust BRIGHTNESS of this projector.

B. Plugging in the power cord

Earthing terminal

2

1

Power cord (Example)

1Plug the attached power cord into the power cord inlet of this projector.

2Plug the other end of the power cord into a power outlet.

The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.

This projector uses the power plug of three-pin grounding type. Do not take away the grounding pin from the power plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.

The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power cord separately.

EN-14

Image 14
Contents HC100 When using the projector in Europe Compliance NoticeContents Important safeguards Do not modify this equipment Place of installationNever remove the cabinet Do not block the air inlet and outlet grillesInserting the batteries into the remote Checking accessoriesPreparating your projector ControlTerminal panel OverviewControl area ButtonAdjustment foot Front Lamp cover Adjustment feet Rear Remote controlUsing the picture quality adjusting buttons Preparating your projector ContinueReception angle Using the remote controlOperational range of the remote control Basic setup Setting up your projectorSetting up the screen Adjusting the projection angleWhen the aspect ratio of the screen is Screen size and projection distanceBasic home theater system connection Connecting the projector to video equipmentViewing video images PreparationsWhen a TV tuner or VCR is connected Connecting to a Video player, etcConnecting to a DVD player Viewing video images Connecting to video equipment having a DVI-D terminalPlugging in the power cord Projecting images PreparationWhen projected images are distorted to a trapezoid To stop projectingWith the remote control Setting the aspect ratioHow to change the settings With the Feature menuViewing computer images Connecting the projector to a computerPlugging the power cord For analog connectionEN-19 Viewing computer images When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonHow to set the menus Menu operationMenu operation Available settings in the menusInstallation menu Image menuFeature menu Signal MenuTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessTo enable the stored color temperature To adjust the tone of white Color TempAbout color temperature LPF Progressive filter Adjusting projected imagesTo adjust the vertical position To enable the password function Advanced featuresPassword function To cancel the password functionInterval of lamp replacement Replacing the lampCleaning of the lens MaintenanceCleaning of the projector and the ventilation slots Reset of the lamp operation timeAsking for installation Dimension Drawings unit mmTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly TroubleshootingProblem Solution Others Problem Solution TemperatureAbnormal condition IndicatorsNormal condition Specifications Replacement part Option / Not included in the boxSpecifications ConnectorsMitsubishi Projector Contact Information North America
Related manuals
Manual 5 pages 33.31 Kb