Mitsubishi Electronics HC1100 Preparating your projector, Checking accessories, Control

Page 6

Preparating your projector

Checking accessories

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.

Cables

Mini D-SUB

 

 

15-pin

D-SUB 9-pin

 

 

 

 

 

Mini D-SUB

8-pin

 

 

15-pin

 

 

 

Audio/Video cable

S-video cable

RGB cable for PC

RS-232C cable

(246C478-10)

(246C479-10)

(246C521-10)

(246C508-10)

Power supply parts

Power cord (two)

(246C483-10, 246C383-20)

Remote control parts

Others

 

• Lens cap (Attached to the

 

projector)

 

• User manual (871D423-30)

 

• Quick Start up (857D064-50)

Remote control

R03 (Size-AAA)

(290P130-10)

battery (two)

Important:

The attached power cords are to be used exclusively for this product. Never use them for other products.

 

Inserting the batteries into the remote

1

control

1.

Remove the rear lid of the remote control.

3

2.

Check the polarity (+), (-) of the batteries, and set them

 

correctly, inserting their (-) side first.

 

• If the battery is inserted from the (+) side first,

2

inserting the (-) side is difficult because the coil spring

end hits on the battery side. If the battery is forced to

insert in this way, the outer label of the battery may get ripped and it may cause a short-circuit and heat- ing.

3. Attach the rear lid.

Important:

• Use two size-AAA batteries (R03).

Replace the two batteries with new ones when the remote control is slow to operate.

CAUTION

Use of a battery of wrong type may cause explosion.

Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

Dispose of used batteries according to your local regulations.

Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.

Be sure to handle the battery according to the instructions.

Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the battery, if the remote control is not used for a long time.

Do not combine a new battery with an old one.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

EN-6

Image 6
Contents HC100 When using the projector in Europe Compliance NoticeContents Important safeguards Do not modify this equipment Place of installationNever remove the cabinet Do not block the air inlet and outlet grillesInserting the batteries into the remote Checking accessoriesPreparating your projector ControlTerminal panel OverviewControl area ButtonAdjustment foot Front Lamp cover Adjustment feet Rear Remote controlUsing the picture quality adjusting buttons Preparating your projector ContinueUsing the remote control Operational range of the remote controlReception angle Basic setup Setting up your projectorSetting up the screen Adjusting the projection angleWhen the aspect ratio of the screen is Screen size and projection distanceBasic home theater system connection Connecting the projector to video equipmentViewing video images PreparationsConnecting to a Video player, etc Connecting to a DVD playerWhen a TV tuner or VCR is connected Connecting to video equipment having a DVI-D terminal Plugging in the power cordViewing video images Projecting images PreparationWhen projected images are distorted to a trapezoid To stop projectingWith the remote control Setting the aspect ratioHow to change the settings With the Feature menuViewing computer images Connecting the projector to a computerPlugging the power cord For analog connectionEN-19 Viewing computer images When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonHow to set the menus Menu operationMenu operation Available settings in the menusInstallation menu Image menuFeature menu Signal MenuTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp About color temperatureTo enable the stored color temperature Adjusting projected images To adjust the vertical positionLPF Progressive filter To enable the password function Advanced featuresPassword function To cancel the password functionInterval of lamp replacement Replacing the lampCleaning of the lens MaintenanceCleaning of the projector and the ventilation slots Reset of the lamp operation timeAsking for installation Dimension Drawings unit mmTroubleshooting No image appears on the screen Problem SolutionTroubleshooting Problem SolutionImages are not displayed correctly Others Problem Solution TemperatureIndicators Normal conditionAbnormal condition Specifications Replacement part Option / Not included in the boxSpecifications ConnectorsMitsubishi Projector Contact Information North America
Related manuals
Manual 5 pages 33.31 Kb