Mitsubishi Electronics HC1100 user manual Projecting images, Preparation

Page 15

C. Projecting images

Preparation:

Remove the lens cap.

Turn on the power of the connected video equipment.

FOCUS ring

ON POWER OFF

COMPONENT button

ENGLISH

ZOOM ring

ON ( I ) button

DVI-D (HDCP)

COMPONENT

DVI COMP VIDEO

COMPUTER

PCS-VIDEO

ENTER

MENUASPECT

COLOR TEMP

VIDEO button S-VIDEO button

POWER button

POWER STATUS

VIDEO button

C.T.GAMMA

AUTO POSITION

VOLUME

A.P.

1.Confirm the POWER indicator lights up red.

If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the power button to turn back on the POWER indicator.

2.Press the POWER button on the projector or ON ( I ) button on the remote control.

It may take about one minute for the lamp to light up.

The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the lens cap.

The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW lamp mode has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.

3.Select an input source.

Press the VIDEO button on the projector or the VIDEO, S-VIDEO or COMPONENT button on the remote control that is corresponding to the terminal in use.

The input source is switched between VIDEO, S-VIDEO and COMPONENT at every press of the VIDEO button on the projector.

Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

Some images become easier to view when the setting of aspect ratio is changed. (See Page 17.)

4.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

5.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See Page 10.)

When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See Page 10.)

6.Adjust the size of the projected image by turning the ZOOM ring.

7.Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

Important :

When a 4:3 image is kept displayed for a long time before displaying 16:9 image, the afterimages of the black bars may appear on the 16:9 image screen. Consult your dealer in this case.

Do not display a still picture for a long time because the afterimages may persist on the screen.

EN-15

Image 15
Contents HC100 Compliance Notice When using the projector in EuropeContents Important safeguards Do not block the air inlet and outlet grilles Place of installationNever remove the cabinet Do not modify this equipmentControl Checking accessoriesPreparating your projector Inserting the batteries into the remoteButton OverviewControl area Terminal panelPreparating your projector Continue Remote controlUsing the picture quality adjusting buttons Adjustment foot Front Lamp cover Adjustment feet RearUsing the remote control Operational range of the remote controlReception angle Adjusting the projection angle Setting up your projectorSetting up the screen Basic setupScreen size and projection distance When the aspect ratio of the screen isPreparations Connecting the projector to video equipmentViewing video images Basic home theater system connectionConnecting to a Video player, etc Connecting to a DVD playerWhen a TV tuner or VCR is connected Connecting to video equipment having a DVI-D terminal Plugging in the power cordViewing video images Preparation Projecting imagesTo stop projecting When projected images are distorted to a trapezoidWith the Feature menu Setting the aspect ratioHow to change the settings With the remote controlFor analog connection Connecting the projector to a computerPlugging the power cord Viewing computer imagesEN-19 Auto Position button When connecting to a notebook computerExample of the setting procedure for external output Viewing computer imagesMenu operation How to set the menusImage menu Available settings in the menusInstallation menu Menu operationSignal Menu Feature menuTo sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintTo adjust the tone of white Color Temp About color temperatureTo enable the stored color temperature Adjusting projected images To adjust the vertical positionLPF Progressive filter To cancel the password function Advanced featuresPassword function To enable the password functionReplacing the lamp Interval of lamp replacementReset of the lamp operation time MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensDimension Drawings unit mm Asking for installationNo image appears on the screen Problem Solution TroubleshootingTroubleshooting Problem SolutionImages are not displayed correctly Temperature Others Problem SolutionIndicators Normal conditionAbnormal condition Replacement part Option / Not included in the box SpecificationsConnectors SpecificationsNorth America Mitsubishi Projector Contact Information
Related manuals
Manual 5 pages 33.31 Kb