Mitsubishi Electronics HC1100 user manual Others Problem Solution, Temperature

Page 33

Others

Problem

Solution

 

 

The exhaust vents

• This air comes out after cooling the inside of the projector. You may feel hot, but

emit warm air.

this is not a malfunction.

 

 

No audio is output.

• Check that the volume isn't set to low.

 

 

The menu can't be

• The microcomputers inside the projector may be wrongly operating because of noise.

used.

Press the POWER button to turn off the lamp and unplug the power cord from

 

the wall outlet. Wait about 10 minutes, plug the power cord in, and try again.

“TEMPERATURE!!”

• This indication appears when the ambient temperature rises high. When the

is displayed.

ambient temperature stays high, the lamp goes out.

 

Eliminate any causes of the rise in the ambient temperature.

 

• This indication appears when the air inlet or outlet grille is blocked. When they are

 

kept blocked, the lamp goes out.

 

Remove the objects blocking the air inlet or outlet grille.

The mark appears.

• This mark appears when ineffective operation is carried out. This isn't a product

 

malfunction.

The remote control

• Check that the battery is loaded in the remote control or the battery isn't weak.

doesn't function

(See page 8.)

easily or at all.

• Check that the remote control sensor isn't exposed to direct sunlight or fluorescent

 

light. (See page 8.)

 

• Use the remote control within its operation range. (See page 8.)

 

• Use the remote control at least 10 cm away from the projector.

The buttons on the

• The password function is working.

control panel (except

Cancel the password lock or contact the person in charge of management of the

for the POWER

projector. (See page 27.)

button) don’t function.

 

Abnormal sound is

• Because the color wheel spins at a high speed, metallic sounds may be heard in

heard.

rare occasions. Such symptom is not a malfunction.

 

 

If the following problem occurs after the lamp is replaced, check the following first.

Problem

Solution

 

 

The projector does

• Fit the lamp cover securely. (See Pages 28 and 29.)

not turn on.

Reset the lamp operating time. (See Page 29.)

 

 

 

The STATUS indicator

Reset the lamp operating time. (See Page 29.)

blinks.

 

 

 

 

 

ENGLISH

Kensington Lock

This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington Technology Group below.

Kensington Technology Group

2855 Campus Drive

San Mateo, CA 94403, U.S.A.

Phone : +1- (650)572-2700 Fax : +1- (650)572-9675

EN-33

Image 33
Contents HC100 Compliance Notice When using the projector in EuropeContents Important safeguards Never remove the cabinet Place of installationDo not modify this equipment Do not block the air inlet and outlet grillesPreparating your projector Checking accessoriesInserting the batteries into the remote ControlControl area OverviewTerminal panel ButtonUsing the picture quality adjusting buttons Remote controlAdjustment foot Front Lamp cover Adjustment feet Rear Preparating your projector ContinueUsing the remote control Operational range of the remote controlReception angle Setting up the screen Setting up your projectorBasic setup Adjusting the projection angleScreen size and projection distance When the aspect ratio of the screen isViewing video images Connecting the projector to video equipmentBasic home theater system connection PreparationsConnecting to a Video player, etc Connecting to a DVD playerWhen a TV tuner or VCR is connected Connecting to video equipment having a DVI-D terminal Plugging in the power cordViewing video images Preparation Projecting imagesTo stop projecting When projected images are distorted to a trapezoidHow to change the settings Setting the aspect ratioWith the remote control With the Feature menuPlugging the power cord Connecting the projector to a computerViewing computer images For analog connectionEN-19 Example of the setting procedure for external output When connecting to a notebook computerViewing computer images Auto Position buttonMenu operation How to set the menusInstallation menu Available settings in the menusMenu operation Image menuSignal Menu Feature menuTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp About color temperatureTo enable the stored color temperature Adjusting projected images To adjust the vertical positionLPF Progressive filter Password function Advanced featuresTo enable the password function To cancel the password functionReplacing the lamp Interval of lamp replacementCleaning of the projector and the ventilation slots MaintenanceCleaning of the lens Reset of the lamp operation timeDimension Drawings unit mm Asking for installationNo image appears on the screen Problem Solution TroubleshootingTroubleshooting Problem SolutionImages are not displayed correctly Temperature Others Problem SolutionIndicators Normal conditionAbnormal condition Replacement part Option / Not included in the box SpecificationsConnectors SpecificationsNorth America Mitsubishi Projector Contact Information
Related manuals
Manual 5 pages 33.31 Kb