PLUS Vision V3-111, V3-131 Operating, Switch on the projector power, Standby button on main unit

Page 22

Power Cable Connections and Switching the Power On/Off

There is an order in which the power cable is connected and the power is switched on/off.

Operating

1 Connect the AC IN connector of the projector and the power outlet using the supplied power cable.

The STANDBY indicator will light in amber, and the unit will enter the standby mode.

STANDBY STATUS

Lit amber

STATUS

 

 

STANDBY

 

 

STANDBY

AUTO

 

 

 

SOURCE

 

 

RGB

 

 

O

 

 

VIDE

AUDIO

S-VIDEO

 

To wall outlet

Firmly plug in all the way.

ECRUO

OTUA S

S

 

Y

UT

 

BD

AT

 

NA

S

Y

TS

 

2

 

BD

 

NA

 

TS

 

2

3

￿Slide the lens shutter to the left until it stops.

￿Press the lift button (marked “PUSH”).

The lens unit rises and projecting is now possible.

Switch on the projector power

Press the STANDBY button.

STANDBY (button on main unit)

Note:

The power will not turn on unless the lens unit is raised.

If the STANDBY button is pressed when the lens is stowed away, the STATUS and STANDBY indicator’s flash orange for several seconds to notify you that the lens is not raised.

The first time the power is switched on after purchase, [Menu Language Select] will be displayed. See Page E-23 for infor- mation about language selection.

•When the power is turned on, the STANDBY indicator starts flashing green, then stops flashing after about 60 seconds. If the STATUS indicator lights green at this time, the lamp mode is set to “Eco”. See E-29 and 51 for instructions on selecting.

•If the power does not come on, see “When the STATUS Indica- tor is Lit or Flashing” on Page E-57.

If the “Password” input window is displayed: See E-34. A password is set for this projector.

The projector cannot be used unless the correct password is in- put.

To turn off the power: See E-24.

HS

UP

1

STANDBY

MENU

RGB

ENTER

VIDEO CANCEL

QUICK

Q

FREEZE MUTE ECO AUTO

1 2 3 4

ASPECT

This indicator is also lit green in Eco-mode.

STANDBY STATUS STANDBY STATUS STANDBY STATUS

Flashing green

Lit green

Lit amber (Approximately 60 Power is on seconds)

The projector is now capable of regular projection.

4 Switch on the power of the connected equipment

Note:

•When the power plug will be unplugged from the power outlet, please place the projector near the power outlet so that it may be reached easily.

•Press the STANDBY button after the STANDBY indicator is lit in amber.

E-22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents
V3-131 Precautions DOC Compliance NoticeCleaning InstallationPower Supply Lamp ReplacementMajor Features Table of Contents Table of Contents Checking the Supplied Accessories Expendables and Options Checking the Supplied AccessoriesV3 Series lamps Model V3-120 ordering code Names of the Main Unit Parts Handling the Lens UnitBuilt-in Security Slot Standby Auto SourceNames of the Remote Control Parts Video / S-VIDEORemote Control Range Preparing the Remote ControlButton Battery Replacement Using the remote control for the first timeProcedure Up to Projecting to the Screen Placement Guide V3-131 Screen Size and Projection DistancePlacement Guide V3-111 Screen Size and Projection DistanceInstallation Height of Projection Screen Reference ExamplePersonal computer RGB signal cable Supplied item Connections with Personal Computer Connecting Personal Computers and Video Equipment To Output the External Output Signal of a Notebook Computer Manufacturer Model Key Video Equipment with S-VIDEO Connectors Connections with Composite SignalsVideo Equipment with Video Connectors Video cable Mini DIN 4-pin plug Commercially availableConnections with Component Signals Connections with the Audio Jack Operating Switch on the projector powerStandby button on main unit This completes the selection of the display language Power Cable Connections and Switching the Power On/OffPress the Enter button to set CursorUnplug the power cable FinishingAdjust the projection image to the screen Adjustment of the Projection ScreenAdjustment of the Projection Screen Turn the focus ring and adjust the focus of the screenAdjuster button Lowering the projection image Making Adjustments with the AdjustersAdjustment of the Projection Screen Raising the projection imageWhen Auto Source is Off Automatic AdjustmentWhen Auto Source is On General OperationSelection of Aspect Ratio Video Signals / Component SignalsGeneral Operation Lamp Mode Cancelling Video and Audio TemporarilyFreezing a Moving Picture Adjustment of the Volume KeystoneImage can also be moved in the following circumstances Enlargement of the Image and Video MovementPress the Zoom button to enlarge the image Timer Display Using the Presentation TimerPress the Enter button and start the timer Moving the Position of the Timer DisplayProtecting the Projector with the Security Lock Canceling the password Input the password using the number buttons 1 toCanceling the password/Changing the password Changing the passwordContent of Adjustments and Settings Using the Quick MenuVolume Menu button Cancel buttonMenu Operation Method Select buttonsMenu Operation Method Adjustment Bar and Settings ContentsMenu Screen Names and Functions Menu Name Cursor Deep BluePerforming Menu Operations Menu Display Press the Menu button to display the menuMaking Adjustments/Settings Sub menuSelecting Another Menu Name with Remote Control Operation Color ViewOption Menu name Item Name Sub Menu SetupInfo Brightness / Contrast / Color / Tint / Sharpness Picture Adj. Picture AdjustmentImage Picture Adj. / Fine Picture / H Position / V PositionPosition ResetFine Picture ImageQuick Color Adj Select the preset color modeColor GammaWhite Selection contents at the time of YPbPr inputColor Temp Color SpaceWhite Balance Aspect Video SignalsView FilterKeystone Save Vertical FlipView Auto Power Off SetupAuto Source Menu Position SetupThis function sets the display position of the menu Input Format Presentation TimerTo start the timer Video and S-VideoOn Screen OptionLanguage BackgroundSecurity Lock Startup ScreenOption Info Factory DefaultLamp Timer Reset StatusLamp Timer Resolution / FrequencyInfo When an Indicator is Lit or Flashing When an Indicator is Lit or Flashing Thermal ProtectorTroubleshooting Check the following matters before requesting servicingCleaning the Inside of the Projector CleaningCleaning a Soiled Projector Main Unit Dirty LensReplacing the Lamp Cartridge Replacing the Lamp Cartridge Remove the lamp cartridgeMount the new lamp cartridge Reset the Lamp TimerMount the lamp cover Electrical SpecificationsOptical MechanicalResolution Frequency Video SignalTable of Supported Frequency Cabinet Dimensions 2003
Top Page Image Contents