PLUS Vision V3-131 Mount the new lamp cartridge, Mount the lamp cover, Reset the Lamp Timer

Page 63

Replacing the Lamp Cartridge

5 Mount the new lamp cartridge.

(1)Push the lamp cartridge in slowly.

(Line it up with the screw holes in the projector.)

(2)Turn the lamp cartridge’s two screws clockwise to tighten them.

6 Mount the lamp cover.

(1)Set the tip of the lamp cover in place, then close the lamp cover.

(2) Turn the lamp cover’s screw clockwise to tighten it.

2

1

7 Reset the Lamp Timer.

Connect the power cable, switch on the power, and then reset.

Select [Info.] → [Lamp Timer Reset] on the menu and press the ENTER button. There is a change to the initialization verification display. Press the ENTER button again. See “Lamp Timer Reset” on Page E-55.

Note:

After reaching the lamp service life, if the lamp is used for more than another 100 hours, it will not be possible to switch on the power. Should this happen, while the projector is in the standby mode, simultaneously holding down the projector’s SOURCE button and AUTO button for more than 5 seconds will clear the lamp timer. Checking that the STATUS indicator is out will show that the lamp timer has been cleared.

Contact a store that sells the V3-131/V3-111 for a replacement lamp. Indicate you need a V3-120 replacement lamp for the V3-131/V3-111 (order code 28-051).

E-63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents V3-131 DOC Compliance Notice PrecautionsLamp Replacement InstallationPower Supply CleaningMajor Features Table of Contents Table of Contents Checking the Supplied Accessories Checking the Supplied Accessories Expendables and OptionsV3 Series lamps Model V3-120 ordering code Handling the Lens Unit Names of the Main Unit PartsStandby Auto Source Built-in Security SlotVideo / S-VIDEO Names of the Remote Control PartsUsing the remote control for the first time Preparing the Remote ControlButton Battery Replacement Remote Control RangeProcedure Up to Projecting to the Screen V3-131 Screen Size and Projection Distance Placement GuideV3-111 Screen Size and Projection Distance Placement GuideExample Installation Height of Projection Screen ReferenceConnections with Personal Computer Personal computer RGB signal cable Supplied itemTo Output the External Output Signal of a Notebook Computer Connecting Personal Computers and Video EquipmentManufacturer Model Key Video cable Mini DIN 4-pin plug Commercially available Connections with Composite SignalsVideo Equipment with Video Connectors Video Equipment with S-VIDEO ConnectorsConnections with Component Signals Connections with the Audio Jack Switch on the projector power OperatingStandby button on main unit Cursor Power Cable Connections and Switching the Power On/OffPress the Enter button to set This completes the selection of the display languageFinishing Unplug the power cableTurn the focus ring and adjust the focus of the screen Adjustment of the Projection ScreenAdjustment of the Projection Screen Adjust the projection image to the screenRaising the projection image Making Adjustments with the AdjustersAdjustment of the Projection Screen Adjuster button Lowering the projection imageGeneral Operation Automatic AdjustmentWhen Auto Source is On When Auto Source is OffVideo Signals / Component Signals Selection of Aspect RatioGeneral Operation Cancelling Video and Audio Temporarily Lamp ModeFreezing a Moving Picture Keystone Adjustment of the VolumeEnlargement of the Image and Video Movement Image can also be moved in the following circumstancesPress the Zoom button to enlarge the image Moving the Position of the Timer Display Using the Presentation TimerPress the Enter button and start the timer Timer DisplayProtecting the Projector with the Security Lock Changing the password Input the password using the number buttons 1 toCanceling the password/Changing the password Canceling the passwordUsing the Quick Menu Content of Adjustments and SettingsVolume Select buttons Cancel buttonMenu Operation Method Menu buttonMenu Name Cursor Deep Blue Adjustment Bar and Settings ContentsMenu Screen Names and Functions Menu Operation MethodMenu Display Press the Menu button to display the menu Performing Menu OperationsSub menu Making Adjustments/SettingsSelecting Another Menu Name with Remote Control Operation View ColorMenu name Item Name Sub Menu Setup OptionInfo Picture Adj. / Fine Picture / H Position / V Position Picture Adj. Picture AdjustmentImage Brightness / Contrast / Color / Tint / SharpnessImage ResetFine Picture PositionGamma Select the preset color modeColor Quick Color AdjColor Space Selection contents at the time of YPbPr inputColor Temp WhiteWhite Balance Filter Video SignalsView AspectVertical Flip Keystone SaveView Setup Auto Power OffAuto Source Setup Menu PositionThis function sets the display position of the menu Video and S-Video Presentation TimerTo start the timer Input FormatBackground OptionLanguage On ScreenStartup Screen Security LockOption Status Factory DefaultLamp Timer Reset InfoResolution / Frequency Lamp TimerInfo When an Indicator is Lit or Flashing Thermal Protector When an Indicator is Lit or FlashingCheck the following matters before requesting servicing TroubleshootingDirty Lens CleaningCleaning a Soiled Projector Main Unit Cleaning the Inside of the ProjectorReplacing the Lamp Cartridge Remove the lamp cartridge Replacing the Lamp CartridgeReset the Lamp Timer Mount the new lamp cartridgeMount the lamp cover Mechanical SpecificationsOptical ElectricalSignal Resolution Frequency VideoTable of Supported Frequency Cabinet Dimensions 2003

V3-111, V3-131 specifications

The PLUS Vision V3-131 and V3-111 are state-of-the-art visual presenters designed to meet the demands of modern educational and business environments. Known for their superior image quality and user-friendly design, these models have gained a reputation for reliability and performance.

The PLUS Vision V3-131 is equipped with a 12-megapixel camera that provides stunning clarity and detail in every image, enabling users to display documents, objects, and other materials with remarkable precision. Its advanced autofocus feature ensures that the focus remains sharp regardless of the distance, making it ideal for showcasing both small and large items. The integrated LED lights illuminate the subject matter without causing glare, enhancing visibility in various lighting conditions.

Conversely, the V3-111 model comes with an 8-megapixel camera, which still delivers high-quality images suitable for most presentations and educational purposes. While slightly lower in resolution than the V3-131, the V3-111 maintains excellent image clarity, making it a cost-effective solution for those not requiring the highest level of detail.

Both models incorporate a versatile design that supports various input sources, including HDMI, USB, and VGA. This connectivity allows users to easily plug into different devices, ensuring seamless transitions between presentations. Additionally, both models feature a USB connection that allows for easy file transfer and direct linkage to computers for enhanced functionality.

One of the standout characteristics of both the V3-131 and V3-111 is their simplicity of use. The intuitive controls are designed for users of all technological backgrounds, allowing for quick adjustments and easy navigation through the menu settings. Furthermore, the flexible arm design enables users to adjust the camera angle and height effortlessly, catering to various presentation scenarios.

In terms of portability, both models are lightweight and compact, making them ideal for frequent use in classrooms and conference rooms. The robust build quality ensures durability while allowing for easy storage between uses.

Overall, the PLUS Vision V3-131 and V3-111 visual presenters exemplify innovation in presentation technology, offering exceptional features such as high-resolution cameras, versatile connectivity, and ease of use. Whether in an educational setting or a corporate environment, these devices provide an effective solution for engaging and impactful presentations.
Top Page Image Contents