Approach Tech NVR-2018 manual Updating System Software

Page 17

3.4 Updating System Software

If the system software of the NVR-2018 needs to be upgraded, please take the following steps to safely update it.

Important: Before carrying out the following procedures, please ensure the SD card is working and the file of system software is intact

1.Create a directory named NVRVIDEO in the SD Card; if the directory is already existed, move to Step2.

2.Copy the file of MULTI.BIN to the NVRVIDEO-directory.

3.If NVR is running, please turn off NVR first.

4.Insert the SD card into the built-in SD slot of the unit.

5.Hold down the Up and Down buttons simultaneously, and then turn on the unit.

6.Keep holding down the buttons until the NVR-2018 sounds a tone and display the message “ XXXXXX BYTES READ” Now the NVR-2018 is updating the system software, which will take approximately 60 seconds to process.

7.Restart the unit when the device sounds a tone twice and displays the messages “PROGRAMMING END” and “ PLEASE RESTART”. The process is complete.

(If you have already followed the procedure 1~5. the unit, however, not being able to power on. Please first check if the SD card you are using is functioning and the file is intact. And then start procedures 1 ~ 5 all over again.)

8.Verify the version of the system software. (Please refer to section 5.7 VERSION option)

PLAY STOP

PAUSE REC

REV

FWD

 

 

 

 

 

 

 

 

 

Seq.

 

Power

Display

Setup

Search

 

 

 

Enter

Shift

A-rec

 

Save

 

CH1

CH2

CH3

CH4

4

8

 

T-rec

 

 

CH5

CH6

CH7

CH8

 

 

DISK

POWER

13 12

Warning: Don’t Interrupt the process while the unit is updating itself and proceed with a SD card containing with no system software of the unit, which would cause the unit hang on.

15

Image 17
Contents Installation Operating Manual Page Safety Precautions Table Of Contents RS-232 Protocol Product Introduction Product FeaturesPage Hard disk compartment lock Front ViewHard-disk drive compartment Rec Indicator Setup/Save buttonLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttonsPower Indicator Disk IndicatorMobile Rack Power LED Shuttle RingRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Basic Connection Connecting with a Single CameraLANCAM, NVR, ROUTER, Connection Structure LAN CameraMaxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowPlayback Operations Operation Status From REC mode to Playback modeFast Forward/Reverse REC → 〔STOP 〕 →Play Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Search Full List Alarm List Time Search Thumbnail SD Card Alarm list SearchSearch Operations Full List SearchDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search SD Card Search Alarm List Time Search Channel : Thumbnail SD CardSearch Thumbnail Year Full List 2003Mobile Rack HD Backup Operations Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALLDisk Setting Reformat HD2 Usage Alarm Select Main Backup AlarmSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Save to J0000.JPG Save to J0001.JPG Save to J000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameResolution Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 REC Setting Bandwidth 10F/SREC Schedule Timer Enable on Timer1200-1800 0600-1800 0000-0000MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingMAX REC Rate Main SET Network RS232RS-232 Main SET IP Pool Range Comm ID IP Pool Range Setting192.168 ― 192.168 Backup HD HD2 Usage HD Backup Full Main Disk REFORMAT/CLEARHD Backup RECSystem Setting Situation From the oldest oneMAC 00 0c 0c 00 00 Bios Date Dec 24 Communication Protocol SetupGeneral Command Format Value of a specific front panel key Statedhcpwait Statesearch Statebackup Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings PIN no Network ViewerInstall the Network Viewer for the ZIP file View the NVR video from a remote PC Page Function Buttons Description Page Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Cable Connections Physical specification of RJ-45 cable for EthernetConnect to a computer Connect to a LAN Hub IntranetConfigure Your NVR Network Settings RJ-45 PIN configuration for LAN HubEnable Dhcp Function Connect to WAN InternetSet IP Address 11.3 TCP/IP Communication Software 11.4 TCP/IP installation Connection Testing 11.5 TCP/IP Configuration settingClick Start Settings Control Panel Network Click Start Programs MS-DOS PromptPage Browsing images from the NVR-2018 Connecting the NVR-2018Description of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Timer Record Setting Model Number 8CH NVR-2018 Design and specifications subject to change without noticeAppendix 1. -SCANIP

NVR-2018 specifications

The Approach Tech NVR-2018 is a state-of-the-art network video recorder designed to meet the demands of modern surveillance systems. With advancements in technology and an emphasis on usability, this NVR serves as a reliable solution for both home and business security needs.

One of the standout features of the NVR-2018 is its high-capacity storage capability. Equipped with support for multiple hard drives, it can accommodate a substantial amount of video footage without compromising performance. Users can opt for various RAID configurations that ensure data redundancy and reliability. This is crucial for environments where continuous monitoring is essential.

Another significant characteristic is the device’s compatibility with a wide array of IP cameras. The NVR-2018 supports various resolutions, including 4MP, 5MP, and even 4K, allowing users to choose the optimum quality for their specific needs. The device incorporates advanced H.265 video compression technology, enabling efficient storage management while maintaining high-quality video output. This not only helps save storage space but also enhances streaming performance, reducing latency and buffering.

Additionally, the Approach Tech NVR-2018 features intelligent video analytics, which can provide users with actionable insights. These features include motion detection, line crossing detection, and facial recognition, making it easier to monitor activities and respond to incidents promptly. The flexibility of remote access through mobile applications and web browsers further enhances usability, allowing users to view live footage and recorded events from anywhere in the world.

The user interface is designed for ease of use, featuring a streamlined, intuitive dashboard that allows quick navigation through multiple camera feeds and settings. Integration with third-party software systems, such as alarm systems and access control, enables a comprehensive surveillance solution tailored to specific operational needs.

The NVR-2018 is built with robust security features to protect against unauthorized access and data breaches. Encryption protocols, user authentication, and automatic firmware updates ensure that the system remains secure and reliable.

Overall, the Approach Tech NVR-2018 combines cutting-edge technology, high-performance capabilities, and user-centric design to deliver a powerful surveillance solution for diverse applications. Its blend of storage capacity, camera compatibility, and intelligent analytics makes it a top choice for users seeking an effective method of monitoring and safeguarding their premises.