Approach Tech NVR-2018 manual Menu Setup

Page 35

5. MENU SETUP

There are 6 categories for operation setting in the setup menu system as shown below. The following sections will instruct you step by step to configure the operation setting and state each menu’s purpose and options. Press the Setup button to access the setup menu. Once inside the menu system, the on-screen menu allows you to set up the key features of the unit. The functions of various buttons within the menu-setup mode are described in the paragraphs below.

MAIN MENU

LAN CAMERA

RECORD / BANDWIDTH

CLOCK / TIMER / SEQ

ALARM

COMMUNICATION

DISK

SYSTEM

KEY FUNCTIONS
Setup button	:
Press to enter the setup menu. Press again to exit the setup mode.
“^” “v” buttons	and	:
Press to select the desired item or entry for setting.
“<” “>” buttons	and	:
Press to highlight the desired option or to select the context for setting.
Enter button	:

Press to enter the selected item and to save the setting.

Shuttle Ring :

Turn to highlight the desired option or to select the context for setting.

Jog Dial :

Turn to select the desired item or entry for setting.

33

Image 35

Contents Installation Operating Manual Page Safety Precautions Table Of Contents RS-232 Protocol Product Introduction Product FeaturesPage Hard disk compartment lock Front ViewHard-disk drive compartment Up / Down CH4-CH8 /CH3-CH7 buttons Setup/Save buttonRec Indicator Left / Right CH1-CH5 /CH2-CH6 buttonsShuttle Ring Disk IndicatorPower Indicator Mobile Rack Power LEDRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Basic Connection Connecting with a Single CameraLANCAM, NVR, ROUTER, Connection Structure LAN CameraMaxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowREC → 〔STOP 〕 → Operation Status From REC mode to Playback modePlayback Operations Fast Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Full List Search Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Search OperationsDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search 2003 Alarm List Time Search Channel ： Thumbnail SD CardSD Card Search Search Thumbnail Year Full ListAlarm Select Main Backup ALL Backup OperationsMobile Rack HD Backup Operations Backup Backup Main EXT Disk SET to Backup 1220 2001-02-01 0330 2001-03-02 0420 1330 Alarm Select Main Backup Alarm Disk Setting Reformat HD2 Usage Search buttonSave to J0000.JPG Save to J0001.JPG Save to J000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameQuality Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Image Setting Quality Highest Medium LOW Lowest SET LancamImage SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 REC Setting Bandwidth 10F/S0600-1800 0000-0000 TimerREC Schedule Timer Enable on 1200-1800MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingMAX REC Rate Main SET Network RS232RS-232 Main SET IP Pool Range Comm ID IP Pool Range Setting192.168 ― 192.168 REC HD Backup Full Main Disk REFORMAT/CLEARBackup HD HD2 Usage HD BackupSystem Setting Situation From the oldest oneMAC 00 0c 0c 00 00 Bios Date Dec 24 Communication Protocol SetupGeneral Command Format Value of a specific front panel key Statedhcpwait Statesearch Statebackup Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings PIN no Network ViewerInstall the Network Viewer for the ZIP file View the NVR video from a remote PC Page Function Buttons Description Page Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Connect to a LAN Hub Intranet Physical specification of RJ-45 cable for EthernetCable Connections Connect to a computerConnect to WAN Internet RJ-45 PIN configuration for LAN HubConfigure Your NVR Network Settings Enable Dhcp FunctionSet IP Address 11.3 TCP/IP Communication Software 11.4 TCP/IP installation Click Start Programs MS-DOS Prompt 11.5 TCP/IP Configuration settingConnection Testing Click Start Settings Control Panel NetworkPage Browsing images from the NVR-2018 Connecting the NVR-2018Description of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Timer Record Setting Model Number 8CH NVR-2018 Design and specifications subject to change without noticeAppendix 1. -SCANIP