Approach Tech NVR-2018 manual Slow Forward/Reverse, Play Back Picture-by-picture

Page 27

4.3.2 Slow Forward/Reverse

There are 5 speeds available for a slow playback: 1/2, 1/4, 1/8, 1/16, 1/32.

While playing back recorded video at the recorded speed:

(1)Press the PAUSE button for the slow playback mode.

(2)Forward: Turn the Shuttle dial to the right to view the recorded video in the forward direction at a speed slower than the recorded speed. Each subsequent turn of the shuttle to the right increases the forward rate, as 1/2, 1/4, 1/8, 1/16, and 1/32.

(3)Reverse: Turn the Shuttle dial to the left to view the recorded video in the reverse direction at a speed slower than the recorded speed. Each subsequent turn of the shuttle to the left increases the reverse rate, as -1/2, -1/4, -1/8, -1/16, and -1/32.

(4)Normal: Release the Shuttle dial and then press the PLAY button to return to the normal speed of playback.

4.3.3Play Back Picture-by-picture

While playing back recorded video at the recorded speed:

(1)Press the PAUSE button for the picture-by-picture mode.

(2)There are two ways, by PAUSE button or by JOG, available to play in the picture-by-picture mode, but the PAUSE button can only function in a forward direction; the other, JOG dial , can act in both a forward and a backward direction, as well as picture-by-picture.

By PAUSE button :

Press the PAUSE button to display one frame/field of a picture at a time in the forward direction. (When playing back video recorded by multi channel, each sequential press of the PAUSE button will display each camera in sequence.)

By JOG dial :

Turn the JOG dial clockwise to display one frame/field of a picture at a time in the forward direction. Turn the JOG dial counterclockwise to display one frame/field of a picture at a time in the backward direction.

(3)Press the PLAY button to return to the normal speed of playback.

4.3.4Play Back Recorded Video from a HDD of the mobile rack

To play back a recorded video from a HD2, take the following steps::

(1)Press the Search button to enter the search mode.

(2)Press the ^” and v” buttons, to select a video; press the <” and >” buttons, to flip over a page.

(3)Use the search function to access desired recorded video. For specific operation details please refer to the next section 4.4 (Search Operations).

25

Image 27
Contents Installation Operating Manual Page Safety Precautions Table Of Contents RS-232 Protocol Product Introduction Product FeaturesPage Front View Hard-disk drive compartmentHard disk compartment lock Up / Down CH4-CH8 /CH3-CH7 buttons Setup/Save buttonRec Indicator Left / Right CH1-CH5 /CH2-CH6 buttonsShuttle Ring Disk IndicatorPower Indicator Mobile Rack Power LEDRear View Alarm In/Out This Figure is Looked from the Rear ViewNo Connection Basic Connection Connecting with a Single CameraLANCAM, NVR, ROUTER, Connection Structure LAN CameraHard-Disk Drive Installation SeagateMaxtor System Information Updating System Software Configuring Recording Settings 352 X Audio OFF720 X Audio OFF Timer Recording Recording OperationsManual Recording Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-00000000-0000 Alarm Recording MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowREC → 〔STOP 〕 → Operation Status From REC mode to Playback modePlayback Operations Fast Forward/ReverseSlow Forward/Reverse Play Back Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Full List Search Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Search OperationsTime Search Thumbnail SearchDD MM Year HH MM 24 / 12 / 2003 00 2003 Alarm List Time Search Channel : Thumbnail SD CardSD Card Search Search Thumbnail Year Full ListAlarm Select Main Backup ALL Backup OperationsMobile Rack HD Backup Operations Backup Backup Main EXT Disk SET to Backup1220 2001-02-01 0330 2001-03-02 0420 1330 Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage Search buttonSave to J0000.JPG Save to J0001.JPG Save to J000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameQuality Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Image Setting Quality Highest Medium LOW Lowest SET LancamImage SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 REC Setting Bandwidth 10F/S0600-1800 0000-0000 TimerREC Schedule Timer Enable on 1200-1800MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingMAX REC Rate Main SET Network RS232Main SET IP Pool Range Comm ID IP Pool Range Setting 192.168 ― 192.168RS-232 REC HD Backup Full Main Disk REFORMAT/CLEARBackup HD HD2 Usage HD BackupSystem Setting Situation From the oldest oneMAC 00 0c 0c 00 00 Bios Date Dec 24 Setup General Command FormatCommunication Protocol Value of a specific front panel key Statedhcpwait Statesearch Statebackup Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings PIN no Network ViewerInstall the Network Viewer for the ZIP file View the NVR video from a remote PC Page Function Buttons Description Page Change the Record & Timer Properties Via the Network Set the regular record settings Set the Alarm record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Connect to a LAN Hub Intranet Physical specification of RJ-45 cable for EthernetCable Connections Connect to a computerConnect to WAN Internet RJ-45 PIN configuration for LAN HubConfigure Your NVR Network Settings Enable Dhcp FunctionSet IP Address 11.3 TCP/IP Communication Software 11.4 TCP/IP installation Click Start Programs MS-DOS Prompt 11.5 TCP/IP Configuration settingConnection Testing Click Start Settings Control Panel NetworkPage Connecting the NVR-2018 Description of functional keysBrowsing images from the NVR-2018 Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Timer Record Setting Model Number 8CH NVR-2018 Design and specifications subject to change without noticeAppendix 1. -SCANIP

NVR-2018 specifications

The Approach Tech NVR-2018 is a state-of-the-art network video recorder designed to meet the demands of modern surveillance systems. With advancements in technology and an emphasis on usability, this NVR serves as a reliable solution for both home and business security needs.

One of the standout features of the NVR-2018 is its high-capacity storage capability. Equipped with support for multiple hard drives, it can accommodate a substantial amount of video footage without compromising performance. Users can opt for various RAID configurations that ensure data redundancy and reliability. This is crucial for environments where continuous monitoring is essential.

Another significant characteristic is the device’s compatibility with a wide array of IP cameras. The NVR-2018 supports various resolutions, including 4MP, 5MP, and even 4K, allowing users to choose the optimum quality for their specific needs. The device incorporates advanced H.265 video compression technology, enabling efficient storage management while maintaining high-quality video output. This not only helps save storage space but also enhances streaming performance, reducing latency and buffering.

Additionally, the Approach Tech NVR-2018 features intelligent video analytics, which can provide users with actionable insights. These features include motion detection, line crossing detection, and facial recognition, making it easier to monitor activities and respond to incidents promptly. The flexibility of remote access through mobile applications and web browsers further enhances usability, allowing users to view live footage and recorded events from anywhere in the world.

The user interface is designed for ease of use, featuring a streamlined, intuitive dashboard that allows quick navigation through multiple camera feeds and settings. Integration with third-party software systems, such as alarm systems and access control, enables a comprehensive surveillance solution tailored to specific operational needs.

The NVR-2018 is built with robust security features to protect against unauthorized access and data breaches. Encryption protocols, user authentication, and automatic firmware updates ensure that the system remains secure and reliable.

Overall, the Approach Tech NVR-2018 combines cutting-edge technology, high-performance capabilities, and user-centric design to deliver a powerful surveillance solution for diverse applications. Its blend of storage capacity, camera compatibility, and intelligent analytics makes it a top choice for users seeking an effective method of monitoring and safeguarding their premises.