Approach Tech NVR-2018 manual Appendix 1. -SCANIP

Page 85

APPENDIX 1. –SCANIP

Follow the instructions below to use the SCANIP software to search the NVR devices from a local location.

1.Click the button to discover the connection of the all-type device in the LAN. The Device List will display the connection of the all-type device.

2.Select the desired device from the Device List.

3.Click the desired device to show the window while the NVR information acts to display the desired changes instantly.

4.Do you want to execute auto search free IP?

If and when you want to auto search the free IP, select “Yes” or “No”. If clicked “Yes” the software will provide the “Free IP Address” boxes on the right side of the window. If you click “No”, these address boxes will not show.

83

Image 85

Contents Installation Operating Manual Page Safety Precautions Table Of Contents RS-232 Protocol Product Introduction Product FeaturesPage Hard-disk drive compartment Front ViewHard disk compartment lock Rec Indicator Setup/Save buttonLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttonsPower Indicator Disk IndicatorMobile Rack Power LED Shuttle RingRear View This Figure is Looked from the Rear View Alarm In/OutNo Connection Basic Connection Connecting with a Single CameraLANCAM, NVR, ROUTER, Connection Structure LAN CameraSeagate Hard-Disk Drive InstallationMaxtor System Information Updating System Software 352 X Audio OFF Configuring Recording Settings720 X Audio OFF Recording Operations Timer RecordingManual Recording Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 W0000-0000 MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Alarm Recording30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams belowPlayback Operations Operation Status From REC mode to Playback modeFast Forward/Reverse REC → 〔STOP 〕 →Play Back Picture-by-picture Slow Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Search Full List Alarm List Time Search Thumbnail SD Card Alarm list SearchSearch Operations Full List SearchThumbnail Search Time SearchDD MM Year HH MM 24 / 12 / 2003 00 SD Card Search Alarm List Time Search Channel ： Thumbnail SD CardSearch Thumbnail Year Full List 2003Mobile Rack HD Backup Operations Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALLDisk Setting Reformat HD2 Usage Alarm Select Main Backup AlarmSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Save to J0000.JPG Save to J0001.JPG Save to J000N.JPG Secure Digital Card SD Card Backup OperationsKey Lock Operation Menu Setup Title Login NameResolution Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 REC Setting Bandwidth 10F/SREC Schedule Timer Enable on Timer1200-1800 0600-1800 0000-0000MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm SettingMAX REC Rate Main SET Network RS232192.168 ― 192.168 Main SET IP Pool Range Comm ID IP Pool Range SettingRS-232 Backup HD HD2 Usage HD Backup Full Main Disk REFORMAT/CLEARHD Backup RECSystem Setting Situation From the oldest oneMAC 00 0c 0c 00 00 Bios Date Dec 24 General Command Format SetupCommunication Protocol Value of a specific front panel key Statedhcpwait Statesearch Statebackup Built-in hard disk Jumper settings of hard-disk drives for the system LocationMobile Rack Page Page D Message Meanings PIN no Network ViewerInstall the Network Viewer for the ZIP file View the NVR video from a remote PC Page Function Buttons Description Page Change the Record & Timer Properties Via the Network Set the Alarm record settings Set the regular record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03Cable Connections Physical specification of RJ-45 cable for EthernetConnect to a computer Connect to a LAN Hub IntranetConfigure Your NVR Network Settings RJ-45 PIN configuration for LAN HubEnable Dhcp Function Connect to WAN InternetSet IP Address 11.3 TCP/IP Communication Software 11.4 TCP/IP installation Connection Testing 11.5 TCP/IP Configuration settingClick Start Settings Control Panel Network Click Start Programs MS-DOS PromptPage Description of functional keys Connecting the NVR-2018Browsing images from the NVR-2018 Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Timer Record Setting Model Number 8CH NVR-2018 Design and specifications subject to change without noticeAppendix 1. -SCANIP