Approach Tech NVR-2018 manual Front View, Hard-disk drive compartment, Hard disk compartment lock

Page 8

2. DESCRIPTION OF THE FRONT/REAR VIEW

2.1 Front View

1

23

2

24

3

4

5

6

PLAY STOP

PAUSE REC

REV

FWD

 

 

 

 

 

 

 

 

Seq.

 

Power

Display

Setup

Search

 

 

 

Enter

Shift

A-rec

 

Save

 

CH1

CH2

CH3

CH4

4 8

 

T-rec

 

 

 

CH5

CH6

CH7

CH8

 

 

 

DISK

POWER

7

8

9

10

11

14

13

12

15

16

17

18

19

20

21

22

Hard-disk drive compartment:

The compartment allows you to install a hard disk drive mostly for backup purposes. Make sure the drive is well secured with the mounting screws in the mobile rack before you put the rack into the compartment. And remember to turn on the power of the compartment by locking it.

Hard disk compartment lock:

The key lock secures a hard disk in place. Unlock the compartment before you remove the hard disk from the slot without turning off the device.

PAUSE button:

In a playback display, press this to freeze the display. During the freeze, press to display one frame/field of a picture at a time in the forward direction. (Illuminate green in PAUSE mode.) PLAY button:

Press to play back a recorded video from the hard disk. (Illuminate green in PLAY mode.) STOP button:

Press to stop playing back a recorded video or recording video into a hard disk. (Illuminate green in STOP mode.)

REC button:

Push to start recording video into a hard disk while in the live display mode. (Illuminate red in REC mode.)

POWER button:

Press this button for at least 3 seconds to power off. Press again to activate the device. DISPLAY button:

Press to show the system operation status on the screen.

In the LANCAM SETTING mode, use these buttons to display the desired LAN Camera image on the screen.

6

Image 8
Contents Installation Operating Manual Page Safety Precautions Table Of Contents RS-232 Protocol Product Features Product IntroductionPage Hard disk compartment lock Front ViewHard-disk drive compartment Setup/Save button Rec IndicatorLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttonsDisk Indicator Power IndicatorMobile Rack Power LED Shuttle RingRear View No Connection Alarm In/OutThis Figure is Looked from the Rear View Connecting with a Single Camera Basic ConnectionLAN Camera LANCAM, NVR, ROUTER, Connection StructureMaxtor Hard-Disk Drive InstallationSeagate System Information Updating System Software 720 X Audio OFF Configuring Recording Settings352 X Audio OFF Manual Recording Timer RecordingRecording Operations Start END 0000-0000 0000-0000 M 0000-0000 W0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 30 SEC Alarm RecordingMAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Motion Detection Sensitivity Highest Region 30, 25 90 Diagrams below Externally triggered RecordingOperation Status From REC mode to Playback mode Playback OperationsFast Forward/Reverse REC → 〔STOP 〕 →Play Back Recorded Video from a HDD of the mobile rack Slow Forward/ReversePlay Back Picture-by-picture Alarm list Search Search Full List Alarm List Time Search Thumbnail SD CardSearch Operations Full List SearchDD MM Year HH MM 24 / 12 / 2003 00 Time SearchThumbnail Search Alarm List Time Search Channel : Thumbnail SD Card SD Card SearchSearch Thumbnail Year Full List 2003Backup Operations Mobile Rack HD Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALLAlarm Select Main Backup Alarm Disk Setting Reformat HD2 UsageSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330Secure Digital Card SD Card Backup Operations Save to J0000.JPG Save to J0001.JPG Save to J000N.JPGKey Lock Operation Menu Setup Login Name TitleQuality Highest Lancam SET Image Resolution Image Setting Resolution Setting CH1 CH2 CH3 CH4Image Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 REC Setting 10F/S BandwidthTimer REC Schedule Timer Enable on1200-1800 0600-1800 0000-0000Alarm Setting MAX REC Rate Unlimit PRE- Alarm Main Alarm REC EnableMAX REC Rate RS232 Main SET NetworkRS-232 Main SET IP Pool Range Comm ID IP Pool Range Setting192.168 ― 192.168 HD Backup Full Main Disk REFORMAT/CLEAR Backup HD HD2 UsageHD Backup RECSystem Setting From the oldest one SituationMAC 00 0c 0c 00 00 Bios Date Dec 24 Communication Protocol SetupGeneral Command Format Value of a specific front panel key Statedhcpwait Statesearch Statebackup Jumper settings of hard-disk drives for the system Location Built-in hard diskMobile Rack Page Page D Message Meanings Network Viewer PIN noInstall the Network Viewer for the ZIP file View the NVR video from a remote PC Page Function Buttons Description Page Change the Record & Timer Properties Via the Network Set the Record Schedule Set the regular record settingsSet the Alarm record settings Archive Images to the Computer Image Viewer 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Point stops recording Previously recorded data remainingPhysical specification of RJ-45 cable for Ethernet Cable ConnectionsConnect to a computer Connect to a LAN Hub IntranetRJ-45 PIN configuration for LAN Hub Configure Your NVR Network SettingsEnable Dhcp Function Connect to WAN InternetSet IP Address 11.3 TCP/IP Communication Software 11.4 TCP/IP installation 11.5 TCP/IP Configuration setting Connection TestingClick Start Settings Control Panel Network Click Start Programs MS-DOS PromptPage Browsing images from the NVR-2018 Connecting the NVR-2018Description of functional keys Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Timer Record Setting Design and specifications subject to change without notice Model Number 8CH NVR-2018Appendix 1. -SCANIP