Philips VCR 462 warranty Glossary, Cable Box/DSS Receiver Output Channel channel 03 or

Page 58

58 Glossary

AUDIO IN/OUT Jacks: jacks located on the front and back of the VCR which are used to record audio from another source (IN) or to send audio to another source (OUT).

The VRX442 has single AUDIO IN/OUT Jacks on the front and back of the VCR. The VRX462 has Right and Left AUDIO IN/OUT Jacks on the front and back of the VCR.

Automatic Channel Programming: process in which the VCR scans all available channels and places the ones you receive in its memory. Then, when you press the CHANNEL Up/Down buttons, you only scan through channels you receive.

Bands: settings that allow you to tune channels.

•Antenna – VHF (very high frequency; channels 2 - 13) and UHF (ultra high frequen- cy; channels 14 - 69).

•Cable – standard channels can be received without a Cable Box.

Cable Box/DSS Receiver Output Channel: channel 03 or 04.

DSS Receiver: Digital Satellite System Receiver.

Dubbing: copying a tape using a second VCR.

Frame: a single still picture.

HQ: high quality; a feature in the VCR circuitry which provides enhanced picture detail.

OTR: one touch recording; programming a timed recording that starts immediately and records for 30 minutes to nine hours, whichever you specify.

Remote Control: the small electronic unit that came with your VCR; allows you to operate your VCR from a distance. The remote control may also operate some fea- tures of your TV, Cable Box, or DSS Receiver.

RF coaxial cable: the cable supplied with your VCR. Use it to connect your VCR to your TV (or Cable Box or DSS Receiver, if applicable). The supplied cable is a snap-on type. However, you may also use a screw-on type if you prefer.

Special Effects: forward and reverse searching; viewing a still picture; or viewing a slow motion picture.

Tape Speeds: how fast the tape travels during a recording or playback.

•LP (long play) – average tape speed (playback time for a T120 tape is approxi- mately four hours); available for playback only. Although the VCR will play tapes recorded in LP, LP will not appear on the display panel or in the on-screen status display.

•SLP (super long play) – slowest tape speed (recording/playback time for a T120 tape is approximately six hours).

•SP (standard play) – fastest tape speed (recording/playback time for a T120 tape is approximately two hours); best picture quality.

VCR: video cassette recorder.

VIDEO IN/OUT Jacks: jacks located on the front and back of the VCR which are used to record video from another source (IN) or to send video to another source (OUT).

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Video Cassette Recorder VRX442 VRX462 Dear Philips Magnavox product owner For Customer UseSafety Precautions FeaturesIntroduction Table of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR MaintenanceHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Antenna Or CableRecording or Viewing a Scrambled or Unscrambled Channel Timer RecordingsHookups With a Cable Box/DSS Receiver Watching TV With the VCR Turned OffPlaying a Tape Hookups With a Cable Box/DSS Receiver cont’dRecording One Channel/Watching Another Antenna in Jack On back of TVVCR will come on and the menu shown below will appear Turning on Your VCRTurn on the TV Press the Menu button. The menu shown below will appear Wait for the VCR to program channelsProgramming Channels Press the Number 3 button to select Tuner SET UPOn the display panel of the VCR Press the Menu button to bring up the main menu display Adding/Deleting ChannelsPress the VCR button Press the Number 4 button to select ADD/DELETE CHPress the Number 3 button to select SET Manual Clock Setting the ClockPress the VCR button, then press the Menu button Press the EXIT/STATUS buttonTime Zone Selection Press the Number 4 button to select SET Time ZoneSetting the Clock cont’d Manual PBS Channel SelectionTurn off the VCR Automatic PBS Channel SelectionPress the EXIT/STATUS button. You will be prompted to ChannelsDaylight-Saving Time Selection Press the EXIT/STATUS button to exitLanguage Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select LanguageRemote Control Buttons VCR PLUS+/ENTER Button Rame ADVance ButtonStop Button EXIT/STATUS ButtonDisplay Panel VRX462Remote Sensor Display Panel cont’dOTR Light Tape Speed Lights Memory LightFront Panel Rear Panel Setting the Remote Control to Operate a TV Find the code for your TV Repeat stepCable BOX/DSS Receiver Codes Find the code for your Cable Box/DSS Receiver Repeat stepSound Program Press the Number 2 button to select on Screen ModeOn-Screen Status Displays On Screen On and Counter Only modesTo program the VCR to find its Remote control only When you find the remote control, point the remote atRemote Locator Read and follow the steps below to play a tape PlayingTurn on the TV Insert a tape Appear on the display panel VCR records in a preset volumeRecording Stop. Details are onStopping an OTR One Touch RecordingStarting an OTR Tape Speed button. Details are on pages 36Press the RECord/OTR button to start a recording Recording One Channel/Watching AnotherInstructions carefully Select a once, daily or weekly recording Timer RecordingPress the Number 1 button to select Program RecordingFollow the instructions in to set the recording’s stop time Instructions continue onThen turn itself off Timer Recording cont’d Tape SpeedsChecking or Clearing Timer Recordings TV Channels Cable Channels Setting Up the VCR Plus+ Programming SystemLocal TV Stations Call letters Examine the lists on 2pageSelect a ONCE, DAILY, or Weekly recording Monday through FridayPress the EXIT/STATUS button. Program WAS COM Connecting the Controller Cable Box or DSS Receiver ControllerPress the Number 5 button to select SET Cable BOX Timer recordingPress the Menu button Press the Menu button or the EXIT/STATUS button Press the Menu button. Wait for a few secondsNumber 2 button to select NO. Use the Number buttons to Cable BOX Control is on will appear for five secondsPress the Number 1 button to set the DSS Receiver Setting the Controller to Operate a DSS ReceiverPress the Number 6 button to select SET DSS Receiver Controller to onPress the Number 1 button to select YES Change the VCR ChannelsVCR 1 will play your tape. Insert a prerecorded tape in VCR Rerecording Tape DuplicationTo the Audio in Jack on VCR Index Search Receiving a Stereo Broadcast These features are not available with the VRX442Receiving a Second Audio Program Multi-Channel Television Sound System VRX462 only cont’d Press the Number 1 button so that on appears besideHi-Fi Stereo Tape Playback VRX462 only Memory light will appear on the display panel Using the Tape CounterTape Counter Memory Turned ON. Details are onGo-To Feature To remove the Goto display, press the GO-TO button againPlay mode Repeat PlaybackVideo Stabilizer Video StabilizerViewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureAutomatic Operation Features Glossary Cable Box/DSS Receiver Output Channel channel 03 orSpecifications Helpful Hints Helpful Hints cont’d Renewed Off mode Ac power cord Hi-fi stereo playback Rewind buttonSafety precautions Automatic With a stereo TV Playback Manually On mode TimerSupplied Accessories
Top Page Image Contents