Clean discs
Wipe the disc with a micro fi bre cleaning cloth from the centre to the edge in a straight line movement.
Specifi cations
Note
•Specifi cation and design are subject to change without notice
USB
•Compatibility:
•Class support: UMS (USB Mass Storage Class) Video
•Signal system: PAL / NTSC
•Composite video output: 1 Vpp ~ 75 ohm
•Component video output: 0.7 Vpp ~ 75 ohm
•HDMI output: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Audio
•Analog stereo output
•Signal to noise ratio (1 kHz): > 90 dB
•Dynamic Range (1 kHz): > 80 dB
•Crosstalk (1 kHz): > 90 dB
•Distortion/noise: (1 kHz): > 75 dB
•MPEG MP3: MPEG Audio L3
•Digital output
• Coaxial
•HDMI output
Main unit
•Dimensions (w x h x d): 360 x 39 x 209 (mm)
•Net Weight: 1.49 kg
Power
•Power supply rating:
•Power consumption: < 10 W
•Power consumption in standby mode: < 0.1 W Accessories supplied
•Remote control and batteries
•HDMI cable
•Audio/Video cables
•AC power cord
•User Manual
Laser specifi cation
•Type: Semiconductor laser InGaAIP (DVD), AIGaAs (CD)
•Wave length: 658 nm (DVD), 790 nm (CD)
•Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD)
•Beam divergence: 60 degrees
9 Troubleshooting
Warning
•Risk of electric shock. Never remove the casing of the product.
To keep the warranty valid, never try to repair the product yourself.
If you have problems using this product, check the following points before you request service. If you still have a problem, register your product and get support at www.philips.com/welcome.
If you contact Philips, you will be asked for the model and serial number of your product.The model number and serial number are on the back of your product.Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Main unit
The buttons on this unit do not work.
•Disconnect this product from the power
outlet for a few minutes, then connect again. No reaction to the remote control.
•Connect this product to the power outlet.
•Point the remote control at the IR sensor located on the front panel of this product.
•Insert the batteries correctly.
•Insert new batteries in the remote control.
Picture
No picture.
•See the TVs user manual on how to select the correct input on the TV. Change the TV channel until you see the Philips screen.
•If you have turned on the progressive scan
setting or change the TV system setting, switch back to default mode: 1) Press 
to open the disc compartment. 2) Press the Numeric button ‘1’ (for progressive scan) or the Numeric button’3’ (for TV system).
No picture on HDMI connection.
•If this product is connected to an unauthorized display device with an HDMI cable, the audio/ video signal may not be output.
•Check if the HDMI cable is faulty. Replace a new HDMI cable.
•If this happens when you change the HDMI
video resolution, you have to switch to its default mode: 1) Press 
to open the disc compartment. 2) Press the numeric button “1”.
Sound
No audio output from the TV.
•Ensure that the audio cables are connected to the audio input of the TV.
•Assign the audio input of the TV to the corresponding video input. See the TV user manual for details.
No audio output from the loudspeakers of the audio device (stereo system/amplifi er/receiver).
•Ensure that the audio cables are connected to the audio input of the audio device.
•Turn on the audio device to its correct audio input source.
English
EN 19