Philips TSU 3000 manual To add an action to the action list, To add a delay to the action list

Page 37

Using the Power Features

User Guide

35

Note You can assign a macro to most buttons of your Pronto NG.

The hard buttons on the left side of Pronto NG (Backlight, Page Up and Page Down) are fixed.

The Toggle and Home button (around the cursor) can only be reprogrammed with ProntoEdit NG.

Please refer to ‘ProntoEdit NG’ on page 49.

To add an action to the action list

1Tap in the ‘Macro’ screen. The last visited page appears again.

2Navigate to the Device and the Page that contains the button you want to add to the macro.

3Tap the button with the action(s) you want to add to the macro. The ‘Macro’ screen appears.

The name of the selected button is added at the bottom of the Action List. The macro will execute all the actions that are assigned to this button.

4You can select other buttons to add to the macro.

To add a delay to the action list

You can add a delay to the action list e.g. to insert a short pause between turning on a device and sending commands to it, allowing the device to warm up.

1Tap in the ‘Macro’ screen.

The ‘+’ button and - button appear on the two middle firm keys below the touch screen.

2To increase the delay, tap (and hold) the firm key labeled ‘+’. -or-

To decrease the delay, tap (and hold) the firm key labeled -’.

Note You can still change the delay later on.

To add a beep to the action list

To determine when the macro execution is finished, it is useful to add a beep as final command in the action list.

1Select the action in the action list, where you want to add a beep. The action is selected.

2Tap in the ‘Macro’ screen.

A default beep is added to the action list, after the selected action.

To test the macro

You do not have to exit the Macro Tool to try out the macro you created or edited. From within the Macro Tool you can test the macro. Pronto NG executes all actions as you defined them in the action list.

Image 37
Contents TSU Page FCC Compliancy Safety & RegulationsFCC Information for User Table of Contents FAQ Pronto NG Home Theater Control Panel Taking a First LookDevice USB port Touch Screen Light sensor What’s New for Pronto Next Generation?Multi Language Support Placing the Batteries Before You StartGetting Started Setting the ContrastTurning on Pronto NG Changing the Time Format Setting Time and DateChanging the Time To change the day Changing the DateTo change the month To change the year Setting the LanguageDevice Overview Operating Pronto NGOverview Customizing Pronto NG Using the ToolsSelecting the Brand and Code Set for your Device Defining the Brand for a DeviceSelecting the brand Installing the brandSelecting the code set Searching the Brand and Code Set for your device Searching the code setSearching the brand Learning CommandsLearning a Device Action Learning a ButtonLabeling Elements Labeling a Button Labeling a Labeling a DeviceAdding a New Device Adding DevicesCopying an Existing Device Deleting a Button Deleting ElementsDeleting a Device Moving DevicesSetting the Timeout of the LCD Backlight Adjusting the SettingsSetting the switch level Setting the Timeout of the LCD ScreenSetting the Navigation for Pronto NG Setting the Volume LevelSetting the Volume Level of the Hard Buttons Setting the Volume Level of the Touch ScreenCalibrating the Touch Screen Setting the Animation ModeCreating and Editing Macros Using the Power FeaturesCreating a Macro To add an action to the action list To add a delay to the action listTo add a beep to the action list To test the macroTo finish the macro Editing a MacroMoving an action in the action list Deleting an action from the action listCreating and Editing Timers Creating and Editing TimersAdding a Timer Labeling a Timer Deleting a TimerEditing a Timer Setting the Start Time or Stop Time Setting the Start DateDefining the Start Action or Stop Action Defining the Repeat Settings Activating Timers Operating Pronto NG with the Cursor To set the cursor navigation Operating Pronto NG with RF Selecting RF to Operate your Devices Selecting IR to Operate your Devices With ProntoEdit NG you can ProntoEdit NGProntoEdit NG How do I calibrate the touch screen? Why don’t my buttons work properly?How do I reset Pronto NG? General Problems TroubleshootingDevices do not respond to commands from Pronto NG Pronto NG shuts off automaticallyButtons are not sending the correct commands Customizing ProblemsPronto NG will not learn commands Configuration file is corruptedPronto NG error messages Memory Storage ProblemsTimers do not work Connection to the PCMaintaining Pronto NG Cleaning Pronto NGImportant Notices Upgrading Pronto NGList of Symbols List of Symbols List of Symbols ProntoEdit NG SpecificationsAction GlossaryLCD USB Index Navigation cursor, 9, 32, 44 touch screen, 32 3104 205