Philips SRC3036/27 user manual Vcr Cbl Dvd Sat

Page 29

Direct Code Entry

Code Search, cont.

1.Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.

2.Press and release the desired mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.

3.Enter the 4 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.

4.With your device on, press CHANNELUP. If the device responds, no further programming is required. Note: If some buttons do not operate your equipment, try one of the other codes for your brand.

Write your codes down here for easy reference later.

Type

Type stored

Code

 

 

 

TV

TV

 

 

 

 

VCR

 

 

 

 

 

CBL

 

 

 

 

 

DVD

 

 

 

 

 

CD

 

 

 

 

 

SAT

 

 

 

 

 

Code Search

If your product does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps.

1.Manually turn on the device (TV, VCR, etc.) to be controlled.

2.Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.

3.Press and quickly release the desired mode button (TV, VCR, etc.). The red indicator blinks off once.

4.Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press the CHANNEL DOWN button to backtrack through the library until the device changes channel. Pressing CHANNEL UP changes direction to forward again.

5.Press and release MUTE to install the code.

8

Most users will store VCR codes under the VCR button, Cable codes under CABLE, etc. If (for example) you want to store a VCR code under CABLE, first follow the procedure for Direct Code Entry (previous page) and press CABLE in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search (or Brand Search, below). Note: If the device does not have a CHANNEL UP button, use PLAY (VCR only) or POWER instead. Code Search starts from the currently stored 4 digit number under that mode.

Code Search by Brand

Lets you search for a code for a specific Brand within the Code Library for a particular manufacturer.

1.Turn on the device (TV, VCR, etc.) to be controlled.

2.Press and hold the SETUP button until the red indicator remains on, then release SETUP button.

3.Press and quickly release the desired mode button (TV, VCR, etc.). The red indicator blinks off once.

4.Press and release the numeric button (0-9) corresponding to desired Manufacturer (see table on code list sheet). The red indicator blinks off once. Note, pressing “0” performs a full library search same as normal Code Search Method on previous page.

5.Press the CHANNEL UP button ((or POWER or PLAY (VCR only)) repeatedly until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press the CHANNEL DOWN button to backtrack through the library until the device changes channel. Pressing CHANNEL UP changes direction to forward again.

6.Press and release MUTE to install the code.

Brand Search Method entry is now complete.

Note: When all codes under a Brand have been searched the red indicator flashes rapidly for 3 seconds.

9

Page 28 Page 30
Image 29
Page 28 Page 30
Contents SRC3036/27 SRU2103/27 Introduction Table of ContentsRECORD, PLAY, STOP, REW, FF, Pause Button Functions Button Functions,DVD Functions SetupCode Search by Brand Direct Code Entry Code Search,Code Search Setup, Code Identification FeatureSleep Timer VCR/DVD/DVR Punch-Through Feature Limited Lifetime Warranty TroubleshootingIntroducción ÍndiceFunciones de botones Funciones de DVD con leyendas en azul PreparaciónInstalación de baterías Ahorrador de bateríasIngreso Directo de Códigos Preparación,Cronometro de apagado automático Función de Identificación de CódigosFunción de traspaso de VCR/DVD/DVR El Control Remoto no Opera su Producto TV/Videocasetera/EntradaProgrammation des codes Saisie des codes Table des matièresRight Fonctions des touches Fonctions des touches,Configuration Programmation au moyen de la fonction de recherche des codes Configuration suiteMinuteur de mise en veille Fonction d’identification des codesCommande Volume/Mute et fonction d’accès direct Le témoin clignote une fois le code programmé DépannageGarantie a vie limitée Page SRU3006L/27 Code Learning Tips on Learning TV, VCR, CBL, DVD, CD, SAT Selects product to DVD Functions labeled in Blue VCR CBL DVD SAT Code Identification Feature VCR/DVD/DVR Punch-Through Feature Tips On Learning, Code LearningIR Transmitter Finder Feature Learning Commands To Clear all Learned Commands under a mode Clearing CommandsDespejar comandos transferidos para una Nota el botón REC debe oprimirse DOS Veces para grabar Entrada TV/Videocasetera/EntradaProgramacíon con Búsqueda de codigos Función de Identificación de Códigos Función de traspaso de VCR/DVD/DVR Consejos Para el Aprendizaje Transferencia de códigosBúsqueda de transmisor IR infrarrojo Aprendizaje de ComandosEl Control Remoto no Opera Algunas Funciones de su Aparato Despejando ComandosIntroduction Fonctions des touches Fonctions DVD et SAT Remarque on doit appuyer deux fois sur la touche REC Input Fonctions DVD en bleuConfiguration suite Contrôle des combinés Accès direct aux modes VCR/DVD/DVR Conseils Sur L’Apprentissage Apprentissage de codesCommandes D’Enregistrement Pour Effacer Toutes Les Commandes Enregistrees Sous Un Mode Suppression des commandes
Top Page Image Contents