Philips SRC3036/27 user manual IR Transmitter Finder Feature Learning Commands

Page 33

IR Transmitter Finder Feature

Learning Commands

This feature assists you in identifying where your original remotes IR transmitter is located and is particularly useful if your original remote’s IR transmitter is hidden behind a lens.

1.Point both remotes facing each other by approximately 1 inch apart (see Tips on Learning on previous pages)

2.Press and hold the SETUP button until the red indicator turns on, then release the button.

3.Press and release the desired Mode button (TV, VCR, etc.), the red indicator blinks then stays on.

4.Press and release the LEARN button, the red indicator blinks then stays on.

5.Press and hold any Original Remote button and move the Original Remote to the left and right, and/ or, up and down in front of the Learning remote IR transmitter. The red indicator will remain on if no IR from the Original remote is found and the red indicator will blink on and off more rapidly when the IR transmitters are lining up. The point where the red indicator blinks most rapidly is where the two IR transmitters are aligned. Note some original remotes will only transmit IR on the initial button press then stop. In these cases, quickly press and release the original remote button repeatedly during this procedure.

6.You can now learn a button from your original remote by continuing from “Step 4” in the “Learning Commands” section on the next page, or, to exit at this point, press and release the SETUP button

16

The learning feature allows you to “learn” functions from your original remote control. For example - you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control. This remote is equipped with an “easy learning” feature that allows you to “learn” features (such as RANDOM PLAY from your original CD remote) by following the steps below, and on the next page:

1.Press and hold the SETUP button until the red indicator turns on, then release the button.

2.Press and release the desired mode button (TV, VCR, etc.), the red indicator blinks then stays on.

3.Press and release the LEARN button, the red indicator blinks then stays on.

4.Press and release the Learning Remote button that you want to teach (e.g. POWER).

5.Point both remotes facing each other by approxi- mately 1 inch apart (see tips on page 14).

6.Press and hold the Original Remote button (e.g. Power) until the red indicator blinks once and stays on. If there is a learning problem, the indicator blinks for three seconds and stays on. If this happens, repeat Steps 4 to 6.

7.Repeat Steps 4-6 for other buttons you want to learn.

8.Press and release the SETUP button when all desired remote commands are learned. Code Learning is now complete.

6.

Line up your remotes (that you’re learning from) in front of the Learning remote, on a hard surface approx. 1 inch apart.

4.

2.

1.

3.

17

Page 32 Page 34
Image 33
Page 32 Page 34
Contents SRC3036/27 SRU2103/27 Introduction Table of ContentsRECORD, PLAY, STOP, REW, FF, Pause Button Functions Button Functions,DVD Functions SetupDirect Code Entry Code Search, Code SearchCode Search by Brand Code Identification Feature Sleep TimerSetup, VCR/DVD/DVR Punch-Through Feature Limited Lifetime Warranty TroubleshootingIntroducción ÍndiceFunciones de botones Funciones de DVD con leyendas en azul PreparaciónInstalación de baterías Ahorrador de bateríasIngreso Directo de Códigos Preparación,Cronometro de apagado automático Función de Identificación de CódigosFunción de traspaso de VCR/DVD/DVR El Control Remoto no Opera su Producto TV/Videocasetera/EntradaProgrammation des codes Saisie des codes Table des matièresRight Fonctions des touches Fonctions des touches,Configuration Programmation au moyen de la fonction de recherche des codes Configuration suiteMinuteur de mise en veille Fonction d’identification des codesCommande Volume/Mute et fonction d’accès direct Dépannage Garantie a vie limitéeLe témoin clignote une fois le code programmé Page SRU3006L/27 Code Learning Tips on Learning TV, VCR, CBL, DVD, CD, SAT Selects product to DVD Functions labeled in Blue VCR CBL DVD SAT Code Identification Feature VCR/DVD/DVR Punch-Through Feature Tips On Learning, Code LearningIR Transmitter Finder Feature Learning Commands To Clear all Learned Commands under a mode Clearing CommandsDespejar comandos transferidos para una Nota el botón REC debe oprimirse DOS Veces para grabar Entrada TV/Videocasetera/EntradaProgramacíon con Búsqueda de codigos Función de Identificación de Códigos Función de traspaso de VCR/DVD/DVR Consejos Para el Aprendizaje Transferencia de códigosBúsqueda de transmisor IR infrarrojo Aprendizaje de ComandosEl Control Remoto no Opera Algunas Funciones de su Aparato Despejando ComandosIntroduction Fonctions des touches Fonctions DVD et SAT Remarque on doit appuyer deux fois sur la touche REC Input Fonctions DVD en bleuConfiguration suite Contrôle des combinés Accès direct aux modes VCR/DVD/DVR Conseils Sur L’Apprentissage Apprentissage de codesCommandes D’Enregistrement Pour Effacer Toutes Les Commandes Enregistrees Sous Un Mode Suppression des commandes
Top Page Image Contents