Philips intelligent remote control manual Now you’re ready to use the new commands

Page 34

5On the remote control, find the button that matches the function on your device’s remote, and tap it once. (Don’t hold it down; simply tap it to make it flash.) Immediately press and hold the corresponding button on the device’s remote control.

First, tap the button on the remote control...

... then immediately press and hold the corresponding button on the source

remote.

When the remote control learns the command, OK ﬂashes brieﬂy on the display. At this point, you can let go of the button you pressed on the source remote. The remote control beeps and then returns to Learn mode.

If after a few seconds the remote control has not learned the command successfully, it buzzes, and FAIL appears brieﬂy on the display. See “Troubleshooting” on page 33.

TIP You can use this same method to program the Mute, Volume, Channel, Left, and Right buttons; see the next sections for special instructions.

6Repeat steps 4 and 5 to program other buttons.

As long as you’re in Learn mode, you can continue to program other soft buttons. You can even use the scroll buttons to navigate to different panels.

If you let the remote control sit idle in Learn mode for ﬁve minutes, it will automatically exit Learn mode and return to the panel that was displayed before you entered Learn mode.

NOTE You can’t test your commands in Learn mode; you must ﬁrst return to Use mode.

7When you’re done, return to Use mode: Tap to open the Mode

menu, and then tap .

Now you’re ready to use the new commands.

32Chapter 3—Customizing the remote control

Image 34

Contents User guide Intelligent Remote Control User Guide User Guide Touch the screen to start Insert batteriesOperate your components Quickreference ModesContents Settings Creating MacrosTroubleshooting Specifications Command ReferenceWelcome Recharging dock FeaturesIntelligent remote control PC serial cableInstalling AA batteries BatteriesBattery Life Using the recharging dock Compartment Light is on while battery is charging Using the remote control Buttons and controlsLeft and Right buttons Direct-access buttonsTouchscreen buttons To turn the display on Getting startedThis is called tapping the screen To adjust the display To turn on the backlightHome Tap one of the buttons to choose a deviceDevice menu Opening the Device MenuChoosing a Device Control panels Scrolling to a Different Control PanelUse mode To switch devices without affecting the source Icon turns around to show a back view of the remote control Customizing the remote control To customize the remote controlOptional Refine your configuration Refer to What are RC-5 and RC-6 CODES? Understanding modes To show or hide the Mode menu To switch modes For help, refer to Use mode on Learning commands from other remote controls Learn mode Buttons that can learn commandsTo program a button on the display soft button Now you’re ready to use the new commands Repeat steps 4 and 5 to program other buttonsTroubleshooting If necessary, tap the Device tab once to extend it To program an item on the Device menuSee the illustration on Remote control ﬂashes the word device To program a template button For instructions, see To relabel a button onProgramming the direct-access and Left/Right buttons To program a button globallyTo program a direct-access button on a per-device basis Remote control displays a choice of buttons Adding devices to your system Add modeTo add a device Choose how you want to add the new device Relabeling buttons and menu items Label mode To relabel a buttonTap the button you want to relabel To relabel an item on a menu To rearrange the items in a menu Rearranging items in menus Move modeFor details, refer to of To relabel a button on After a few seconds, the remote control returns to Use mode Deleting buttons and menu items Delete mode To delete a button or button actionTo delete a device, Device menu action, or macro group Macro menu open in Delete Restoring Deleted BUTTONS, DEVICES, and Macro Groups Creating Macros Editing Macros Recording macros To record a macroWill belong to.Room for new macros on this panel Tap an empty button to start a new macro When you’re done, tap the Macro tab Troubleshooting Macros Contents of the macro appear on the display To view the commands in a macroTo view the commands in a macro while in Use mode Editing macrosEdit the macro To add a macro group Organizing macros into groupsDisplay any macro panel or individual macro Deleting Macros and Macro Groups To execute a macro Using macrosTo stop a macro Settings To adjust settingsAdjust the settings as described in the following tables DurationButtons TouchscreenBeep of the direct Need to use the Revert buttonTo exit Setup Troubleshooting Problems using the remote controlButtons AREN’T Sending the Right Commands Remote Control WON’T LEARN/LABEL/DELETE Commands Problems using the recharging dock Remote Control Error MessagesCommon questions Additional procedures To reset the remote controlTap Cancel to exit without reverting To revert to the original configurationRemote control asks you to conﬁrm your choice To calibrate the touchscreenSeven programmable direct-access buttons Speciﬁcations for the intelligent remote controlHigh-resolution 320 ⋅ 240 liquid crystal display with Backlighting for LCD and direct-access buttons110/220V-to-12V power adapter Automatic on/off no power switchNiMH 4.8V rechargeable battery pack 138 mm ⋅ 92 mm ⋅ 38 mmCommand Reference Install Open / Close Cancel pictureSwitch screen a to B Video outputButton Command Conﬁrm entry Serial Cable What is ProntoEditHow to receive ProntoEdit ProntoEdit System RequirementsService and support 8622 405