Philips intelligent remote control manual Additional procedures, To reset the remote control

Page 73

Additional procedures

To reset the remote control

The remote control’s reset button is accessible through a small hole on the back of the remote control. Under normal circumstances, you should never need to reset the remote control. However, if the display freezes or you notice other unusual behavior, you might need to use the reset button to get the remote control working again.

To reset the remote control:

•Using the tip of an unfolded paperclip, gently press the Reset button located deep within the remote control unit.

You might feel some resistance when you press down. When you have pressed the Reset button, the remote control starts up. After a few seconds, the remote control beeps, indicating that it’s ready to use.

Reset button

NOTE You will not lose custom commands and macros that you have saved. However, if you were making changes to the remote control in a mode other than Use, and you quit before you saved changes, you will lose the changes.

Additional procedures

71

Image 73

Contents User guide Intelligent Remote Control User Guide User Guide Touch the screen to start Insert batteriesOperate your components Modes QuickreferenceContents Creating Macros SettingsSpecifications Command Reference TroubleshootingWelcome Intelligent remote control FeaturesRecharging dock PC serial cableBatteries Installing AA batteriesBattery Life Using the recharging dock Compartment Light is on while battery is charging Buttons and controls Using the remote controlLeft and Right buttons Direct-access buttonsTouchscreen buttons To turn the display on Getting startedThis is called tapping the screen To turn on the backlight To adjust the displayTap one of the buttons to choose a device HomeOpening the Device Menu Device menuChoosing a Device Scrolling to a Different Control Panel Control panelsUse mode To switch devices without affecting the source Icon turns around to show a back view of the remote control To customize the remote control Customizing the remote controlOptional Refine your configuration Refer to What are RC-5 and RC-6 CODES? Understanding modes To show or hide the Mode menu To switch modesFor help, refer to Use mode on Buttons that can learn commands Learning commands from other remote controls Learn modeTo program a button on the display soft button Repeat steps 4 and 5 to program other buttons Now you’re ready to use the new commandsTroubleshooting If necessary, tap the Device tab once to extend it To program an item on the Device menuSee the illustration on Remote control ﬂashes the word device For instructions, see To relabel a button on To program a template buttonTo program a button globally Programming the direct-access and Left/Right buttonsTo program a direct-access button on a per-device basis Remote control displays a choice of buttons Adding devices to your system Add modeTo add a device Choose how you want to add the new device To relabel a button Relabeling buttons and menu items Label modeTap the button you want to relabel To relabel an item on a menu To rearrange the items in a menu Rearranging items in menus Move modeFor details, refer to of To relabel a button on After a few seconds, the remote control returns to Use mode To delete a button or button action Deleting buttons and menu items Delete modeTo delete a device, Device menu action, or macro group Macro menu open in Delete Restoring Deleted BUTTONS, DEVICES, and Macro Groups Creating Macros Editing Macros To record a macro Recording macrosWill belong to.Room for new macros on this panel Tap an empty button to start a new macro When you’re done, tap the Macro tab Troubleshooting Macros To view the commands in a macro while in Use mode To view the commands in a macroContents of the macro appear on the display Editing macrosEdit the macro To add a macro group Organizing macros into groupsDisplay any macro panel or individual macro Deleting Macros and Macro Groups To execute a macro Using macrosTo stop a macro To adjust settings SettingsDuration Adjust the settings as described in the following tablesBeep of the direct TouchscreenButtons Need to use the Revert buttonTo exit Setup Problems using the remote control TroubleshootingButtons AREN’T Sending the Right Commands Remote Control WON’T LEARN/LABEL/DELETE Commands Remote Control Error Messages Problems using the recharging dockCommon questions To reset the remote control Additional proceduresRemote control asks you to conﬁrm your choice To revert to the original configurationTap Cancel to exit without reverting To calibrate the touchscreenHigh-resolution 320 ⋅ 240 liquid crystal display with Speciﬁcations for the intelligent remote controlSeven programmable direct-access buttons Backlighting for LCD and direct-access buttonsNiMH 4.8V rechargeable battery pack Automatic on/off no power switch110/220V-to-12V power adapter 138 mm ⋅ 92 mm ⋅ 38 mmCommand Reference Switch screen a to B Cancel pictureInstall Open / Close Video outputButton Command Conﬁrm entry How to receive ProntoEdit What is ProntoEditSerial Cable ProntoEdit System RequirementsService and support 8622 405