Philips intelligent remote control manual Touchscreen, Beep of the direct, Buttons

Page 66

Second Setup panel
Setting	What it does		How to adjust it

Light Sensor	Shows the current level of light in the room (ambient light).
Set Level	Sets the light level at		Tap Level, then use the Left (-)
	which the light sensor		and Right (+) buttons to
	turns the backlight on.		increase or decrease the
			sensitivity.
			To set the level relative to the
			current lighting, ﬁrst tap Set; the
			Level indicator shows the
			current light level. Then use the
			Left and Right buttons to
			increase or decrease the
			sensitivity.
Mode Menu	Hides or shows the		Tap the Mode Menu button
	Mode button	on	once.
	the display. Hiding the
	Mode button prevents
	unwanted changes to
	stored commands.

Touchscreen	Adjusts or turns off the
Beep	touchscreen beep.

Tap repeatedly to cycle through four volume levels, including off.

Button Beep	Adjusts or turns off the
	beep of the direct-
	access, Left, and Right
	buttons.

Tap repeatedly to cycle through four volume levels, including off.

Calibrate	Calibrates the touchscreen.
	See Chapter 6, “Troubleshooting.” You won’t normally
	need to adjust the calibration.
Revert	Reverts to the factory default conﬁguration. All customization
	and programming is lost.
	See Chapter 6, “Troubleshooting.” You won’t normally
	need to use the Revert button.

64Chapter 5—Settings

Image 66

Contents User guide Intelligent Remote Control User Guide User Guide Insert batteries Touch the screen to startOperate your components Quickreference ModesContents Settings Creating MacrosTroubleshooting Specifications Command ReferenceWelcome Recharging dock FeaturesIntelligent remote control PC serial cableInstalling AA batteries BatteriesBattery Life Using the recharging dock Compartment Light is on while battery is charging Using the remote control Buttons and controlsDirect-access buttons Left and Right buttonsTouchscreen buttons Getting started To turn the display onThis is called tapping the screen To adjust the display To turn on the backlightHome Tap one of the buttons to choose a deviceDevice menu Opening the Device MenuChoosing a Device Control panels Scrolling to a Different Control PanelUse mode To switch devices without affecting the source Icon turns around to show a back view of the remote control Customizing the remote control To customize the remote controlOptional Refine your configuration Refer to What are RC-5 and RC-6 CODES? Understanding modes To switch modes To show or hide the Mode menuFor help, refer to Use mode on Learning commands from other remote controls Learn mode Buttons that can learn commandsTo program a button on the display soft button Now you’re ready to use the new commands Repeat steps 4 and 5 to program other buttonsTroubleshooting To program an item on the Device menu If necessary, tap the Device tab once to extend itSee the illustration on Remote control ﬂashes the word device To program a template button For instructions, see To relabel a button onProgramming the direct-access and Left/Right buttons To program a button globallyTo program a direct-access button on a per-device basis Adding devices to your system Add mode Remote control displays a choice of buttonsTo add a device Choose how you want to add the new device Relabeling buttons and menu items Label mode To relabel a buttonTap the button you want to relabel To relabel an item on a menu Rearranging items in menus Move mode To rearrange the items in a menuFor details, refer to of To relabel a button on After a few seconds, the remote control returns to Use mode Deleting buttons and menu items Delete mode To delete a button or button actionTo delete a device, Device menu action, or macro group Macro menu open in Delete Restoring Deleted BUTTONS, DEVICES, and Macro Groups Creating Macros Editing Macros Recording macros To record a macroWill belong to.Room for new macros on this panel Tap an empty button to start a new macro When you’re done, tap the Macro tab Troubleshooting Macros Contents of the macro appear on the display To view the commands in a macroTo view the commands in a macro while in Use mode Editing macrosEdit the macro Organizing macros into groups To add a macro groupDisplay any macro panel or individual macro Deleting Macros and Macro Groups Using macros To execute a macroTo stop a macro Settings To adjust settingsAdjust the settings as described in the following tables DurationButtons TouchscreenBeep of the direct Need to use the Revert buttonTo exit Setup Troubleshooting Problems using the remote controlButtons AREN’T Sending the Right Commands Remote Control WON’T LEARN/LABEL/DELETE Commands Problems using the recharging dock Remote Control Error MessagesCommon questions Additional procedures To reset the remote controlTap Cancel to exit without reverting To revert to the original configurationRemote control asks you to conﬁrm your choice To calibrate the touchscreenSeven programmable direct-access buttons Speciﬁcations for the intelligent remote controlHigh-resolution 320 ⋅ 240 liquid crystal display with Backlighting for LCD and direct-access buttons110/220V-to-12V power adapter Automatic on/off no power switchNiMH 4.8V rechargeable battery pack 138 mm ⋅ 92 mm ⋅ 38 mmCommand Reference Install Open / Close Cancel pictureSwitch screen a to B Video outputButton Command Conﬁrm entry Serial Cable What is ProntoEditHow to receive ProntoEdit ProntoEdit System RequirementsService and support 8622 405