Philips 32PW9631/12 manual Headphone, Extra loudspeakers

Page 37

n

			REAR
8	m	m
	m		FRONT


		R	L

Headphone

4Insert the plug into the headphone socket n at the front of the TV.

4Press c on the remote control to switch off the internal loudspeakers of your TV.

The headphone socket has an impedance of between 8 and 4000 Ohm and is of the 3.5 mm jack type.

In the SOUND menu select Headphone to adjust the headphone volume and balance and to select the audio source for your headphone sound.

See page 17.

English

	Extra loudspeakers
	You can replace the left and right internal loudspeakers of your set by two
4	extra loudspeakers, min. 8 Ohm.
4	Connect the loudspeakers to the connector clips at the back of the TV.
4	Push the connector clip down and insert the ends of the wires into the
	openings :
	the negative wires to the black connector clips, the positive wires (the one
	with a black line) to the red connector clips.
4	Do not insert the wires too far.
4	Connect the front left loudspeaker to FRONT L and the front right loudspeaker
4	to FRONT R.
4	Put the loudspeaker switch on the back in the c position.
5	The internal right and left loudspeakers of your TV are now switched off.

37

Image 37

Contents Contents Menu p.13 Your remote controlVideo recorder Picture In PictureSurround Sound loudspeakers PreparationRemote control Switch TV onSelect Country Select the menu languagePress OK Manual installation Automatic installationPress Menu Installation menu reappears Go on to Store TV channelsSearch for a TV channel Manual installationNo channel found ? Connected properly. See Tips pRepeat End Store steps 1 to Enter the programme numberDirect selection of a TV channel Press MenuReshuffle the programme list Enter or modify a programme nameSelect Favourite TV channels Install TV ConfigurationExternal amplifier Surround ModePicture tilt Information LineFast exit from the menus Keep the Menu key pressed to switch off all menusSelect Programme with the keys V or W Programme lights upSwitch to standby Switch TV onAdjust the volume Switch menus on and offAdjust picture settings Select the picture settingsMain Menu SharpnessDynamic Contrast TintAdjust sound settings Select the sound settingsSelect Graphic Equalizer with the keys V or W and press OK Select the sound styles with the sound menuSwitch Loudness on or off Select the sound modeSelect Speech Select Spatial soundSurround Mode lights up Dolby* Pro Logic InstallPro Logic with Dolby Surround broadcasting Marked with Dolby SurroundLocal menu adjustments disappear Sleeptimer FeaturesChild Lock General PP StoreMessage Press OK when you have entered the complete messageStart Time lights up TimersRecording Source Select Programme listPicture format Other functionsMaking subtitles visible Information on screen Bilingual broadcastSelect previous programme Press the 2 key Previously selected TV channel is displayedPermanent Programme Number Adjust BrightnessClock Freeze the picturePP key Open the door of the remote control Press MScan Mosaic screenSelect a TV channel with the digit keys Photo FinishPip Picture in Picture Switch pip on and offSelect pip programmes Select pip connectionsSelect Still Picture Switch screensMove the pip screen Teletext Switch Teletext on and offAbout the Easy Text system Select a TeletextSelect subpages Quickly run through the teletext pagesSelect the index teletext Select Special teletext functions Select Continuous SubtitlesConnect Peripheral Equipment Search for and store the test signal of the video recorderTV and video recorder Audio equipment TV and a CD-i/Photo CDCamera and camcorder CD-i/Photo CD lights upExtra loudspeakers HeadphoneConnect a decoder with an aerial socket to the TV DecoderConnect a decoder without an aerial socket to the TV Connect the decoder to your TV with a eurocable 3 onlyCable Switch your TV onRecord with a video recorder Keep Menu pressed for a short while to switch off each menuRecord a TV programme VCR Operate the video recorder with the TV remote controlEnd of life directives TipsIndex