Philips CCA134AT owner manual ONE Time Program Channel Time on

Page 35

Timer Recording (cont’d) 35

4

Use the Number buttons (1-8) to select a position in which to store the timer recording. Flashing numbers indi- cate an open position (one in which a timer recording has not been stored yet).

NOTE: If you select a number that already has been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen for a few seconds. Then information about the program in that position will appear on the screen. If this happens, press the STATUS/EXIT but- ton. Then use the Number buttons to select another position.

5

Use the Number buttons to enter the channel of the TV program you want to record.

●If you are recording from line input, press 0, 0. A/V IN will appear on the screen.

●If you are recording using a Cable Box, enter the Cable Box output channel (03 or 04). Be sure to select the channel of the TV program at the Cable Box and leave the Cable Box on for the timer recording.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL – – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

6

Press two Number buttons for the hour(s) you want the recording to begin. Press two Number buttons for the minute(s) you want the recording to begin. Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

7

Follow the instructions in step 6 to set the recording’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM 1

CHANNEL	10
TIME ON	09:30 PM
TIME OFF	– – : – –

TO CORRECT PRESS CLEAR

TO END PRESS EXIT

Instructions continue on page 36.

4-7

POWER		EJECT
SLEEP/WAKE UP	SPEED	MEMORY
REC/OTR		PAUSE/STILL

	PLAY
REW		F.FWD
	STOP
MENU	STATUS/EXIT	CLEAR

1		2	3
4		5	6	CH.
4		5	6
7		8	9
A.CH		0		VOL.
				VOL.
CABLE/DBS	COMBI
		VCR PLUS+
VAR.SLOW			/ENTER	MUTE
TRACKING			F.ADV	SLOW
SMART		SKIP	INDEX
PICTURE		SEARCH SEARCH

Helpful Hints

•If the numbers entered do not match the TV/VCR’s calendar, the entry will be rejected and a question mark will appear on the screen.

•To make corrections while you are programming a timer recording, press the CLEAR button until the cursor is flashing on the item you want to change. Then enter the cor-

rect information.

Image 35

Contents CCA134AT RA T I O Dear Philips Magnavox product ownerFor Customer Use Model No Serial NoIntroduction FeaturesSafety Precautions Table of Contents Erasure Prevention Putting Batteries in the Remote ControlUsing the Remote Control TV/VCR MaintenanceRod Antenna Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR RF coaxial cable Not suppliedCable Plug Hooking Up the TV/VCR cont’dBent pin Crooked Pin Straight PinEspañol Select KL or Press Menu to Continue Turning On the TV/VCRPress the Menu button. The screen shown below will appear Select Language EnglishPress the Combi button, then press the Menu button PRIM. SetupVCR Program VCR Setup Caption Reminder Language SelectionPress B Automatic Channel SetupProgramming of the channel you added or deleted will appear Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Repeat steps 3-4 to add or delete other channelsCable Box users must set the clock manually Setting the ClockManual Clock Setting To Correct Press Clear To END Press Exit SET Manual Clock TimeMonth To Correct Press Clear To END Press Exit DateAutomatic PBS Channel Selection Setting the Clock cont’dNOW Searching Wait for the TV/VCR to findTime SET Auto Clock TimeManual PBS Channel Selection Auto Clock PBS CH Time Date NOW Searching To END Press Exit Use the Number buttons to select your PBS stationNOW Searching flashes on the TV/VCR screen Wait for the TV/VCR to find the timeTime Daylight Savings Time Primary SetupDaylight-Savings Time Press the PLAY/ button or the STOP/ button to select PRIM. SETUP. Then, press the F.FWD/B buttonTime Zone Cable BOX Codes Setting the Remote to Operate a Cable Box/DBSSetting the Remote to Operate a Cable Box/DBS cont’d Front Panel Connect your antenna or cable here. Details are on page six AC Power CordRear Panel ANTenna JackRemote Control Buttons REWind/ Button VOLume m/n ButtonPAUSE/STILL Button Memory ButtonPress the REWind/ button or the F.FWD/B button to Adjusting the Picture ControlsAdjust the picture control. Refer to the chart on When you finish, press the STATUS/EXIT buttonSofter Adjusting the Picture Controls cont’dDecrease Increase More brilliantIf you select Status OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status ON, then select Counter only onInsert a tape in the TV/VCR PlayingPress the RECord/OTR button once to start recording Power button to turn on the TV/VCR, if necessaryRecording OTR Length Press OTR Cancel Press ClearOTR Different brands of equipment may operate differently Rerecording Tape DuplicationFollow the steps below to prevent accidental recording VCR Program VCR Setup CaptionVCR Setup ONE Time Play Repeat Play ON-SCREEN Mode Defeat RecordingSelect Program Number To END Press Exit Timer RecordingDaily Time OFF To Correct Press Clear To END Press Exit ONE Time Program Channel Time onTimer Recording cont’d Checking or Clearing Timer Recordings Station Setting Up the VCR Plus+ Programming SystemTV Channels VCR PLUS+ Cross REF. MAP VCR PLUS+ CABLE/TV Examine the lists onVCR PLUS+ Cross REF. MAP To Select CH Press then Enter CH NO. to END Press ExitTo SET Press VCR + To Correct Press Clear To END Press Exit You have completed the steps on pagesVCR PLUS+ Program Timer Recording With the VCR Plus+ Programming System cont’d Appear on the screen Real-Time Counter MemoryVCR Setup ONE Time Play VCR Program VCR SetupRepeat Play B Repeat PlayRepeat Flashing a will become a flashing BViewing a Still Picture Playback OptionsForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPGround Blue BackgroundTo block ratings, follow the steps below SmartLockExample Specific Sub-ratings SmartLock cont’dRatings are defined on After you enter the code, the Smartlock menu will appear To change the access code, follow these stepsTV-Y7 TV-G To check the SmartLock settings, follow these stepsBlocked Ratings Press the Combi button, then press the SLEEP/WAKE UP button Sleep TimerTimer during a recording Timer Sleep Wake UP Timer Sleep Wake UP TV on ON-TIMEScreen Closed CaptionExample MenuHalf-screen text Closed Caption cont’dStandard Closed Captions Volume Bar Automatic Operation Features Smart Picture TV ResetPress the Mute button, then press the PAUSE/STILL button If another remote control beepsReminder Brightness Picture Color Tint Sharpness ReminderIndex Search Enter Index Number Tape in the TV/VCRSpecifications Glossary Helpful Hints Helpful Hints cont’d Model # Serial # Limited WarrantyPlease contact Philips at French Speaking English Speaking Index Supplied Accessories