Philips CCA134AT owner manual Flashing a will become a flashing B, Repeat

Page 45

A-B Repeat Play (cont’d) 45

6

Press the STATUS/EXIT button to remove the menu. A- B REPEAT will appear on the screen. Beneath it, the letter A will flash beside the real-time counter.

.

A-B REPEAT

A 0:12:34

76

Play, fast forward, or rewind the tape to the position at which you want to begin playback. Stop the tape, then press the MEMORY button to set the start position (A).

The flashing A will become a flashing B.

.

A-B REPEAT

B 0:00:00

8

Play or fast forward the tape to the position at which you want playback to end. Stop the tape, then press the MEMORY button to set the end position (B).

The length of time between the start position (A) and the end position (B) must be at least three minutes.

7-8

POWER

 

EJECT

SLEEP/WAKE UP

SPEED

MEMORY

REC/OTR

 

PAUSE/STILL

 

PLAY

 

REW

 

F.FWD

 

STOP

 

MENU

STATUS/EXIT

CLEAR

1

 

2

3

 

4

 

5

6

CH.

 

 

7

 

8

9

 

A.CH

 

0

 

VOL.

 

 

 

 

CABLE/DBS

COMBI

 

 

 

 

VCR PLUS+

 

VAR.SLOW

 

/ENTER

MUTE

TRACKING

 

F.ADV

SLOW

SMART

 

SKIP

INDEX

 

PICTURE

 

SEARCH SEARCH

 

9

The TV/VCR will immediately rewind the tape to the start posi- tion (A) and repeat playback to the end position (B) over and over.

(TV programming will appear while the tape is rewinding.)

Helpful Hints

The counter cannot be memorized or reset when you are using this feature.

Positions A and B will be erased when you press the REC(ord)/OTR button.

A-B REPEAT will not appear on the screen at step 6 if a tape is not in the TV/VCR. NO CASSETTE will flash on the screen briefly.

You cannot rewind or fast forward beyond points A or B when you are using this feature.

A-B Repeat Play will be retained if you turn off the TV/VCR power. However, if you eject the tape, A-B Repeat Play will be cancelled.

Image 45
Contents CCA134AT For Customer Use Dear Philips Magnavox product ownerModel No Serial No RA T I OFeatures Safety PrecautionsIntroduction Table of Contents Using the Remote Control Putting Batteries in the Remote ControlTV/VCR Maintenance Erasure PreventionHooking Up the TV/VCR Hook up your TV/VCR using one of the connections shownRF coaxial cable Not supplied Rod AntennaBent pin Hooking Up the TV/VCR cont’dCrooked Pin Straight Pin Cable PlugPress the Menu button. The screen shown below will appear Turning On the TV/VCRSelect Language English Español Select KL or Press Menu to ContinueVCR Program VCR Setup Caption Reminder PRIM. SetupLanguage Selection Press the Combi button, then press the Menu buttonPress B Automatic Channel SetupPress the PLAY/o button or the STOP/p button to select Adding/Deleting ChannelsRepeat steps 3-4 to add or delete other channels Programming of the channel you added or deleted will appearSetting the Clock Manual Clock SettingCable Box users must set the clock manually Month To Correct Press Clear To END Press Exit SET Manual Clock TimeDate To Correct Press Clear To END Press ExitAutomatic PBS Channel Selection Setting the Clock cont’dTime Wait for the TV/VCR to findSET Auto Clock Time NOW SearchingManual PBS Channel Selection NOW Searching flashes on the TV/VCR screen Use the Number buttons to select your PBS stationWait for the TV/VCR to find the time Auto Clock PBS CH Time Date NOW Searching To END Press ExitPrimary Setup Daylight-Savings TimeTime Daylight Savings Time PRIM. SETUP. Then, press the F.FWD/B button Time ZonePress the PLAY/ button or the STOP/ button to select Cable BOX Codes Setting the Remote to Operate a Cable Box/DBSSetting the Remote to Operate a Cable Box/DBS cont’d Front Panel Rear Panel AC Power CordANTenna Jack Connect your antenna or cable here. Details are on page sixRemote Control Buttons PAUSE/STILL Button VOLume m/n ButtonMemory Button REWind/ ButtonAdjust the picture control. Refer to the chart on Adjusting the Picture ControlsWhen you finish, press the STATUS/EXIT button Press the REWind/ button or the F.FWD/B button toDecrease Increase Adjusting the Picture Controls cont’dMore brilliant SofterIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status OFFInsert a tape in the TV/VCR PlayingPower button to turn on the TV/VCR, if necessary RecordingPress the RECord/OTR button once to start recording Length Press OTR Cancel Press Clear OTROTR Different brands of equipment may operate differently Rerecording Tape DuplicationVCR Setup ONE Time Play Repeat Play ON-SCREEN Mode VCR Program VCR Setup CaptionDefeat Recording Follow the steps below to prevent accidental recordingTimer Recording DailySelect Program Number To END Press Exit Time OFF To Correct Press Clear To END Press Exit ONE Time Program Channel Time onTimer Recording cont’d Checking or Clearing Timer Recordings Setting Up the VCR Plus+ Programming System TV ChannelsStation VCR PLUS+ Cross REF. MAP Examine the lists onTo Select CH Press then Enter CH NO. to END Press Exit VCR PLUS+ Cross REF. MAP VCR PLUS+ CABLE/TVYou have completed the steps on pages VCR PLUS+ ProgramTo SET Press VCR + To Correct Press Clear To END Press Exit Timer Recording With the VCR Plus+ Programming System cont’d Appear on the screen Real-Time Counter MemoryVCR Setup ONE Time Play VCR Program VCR SetupRepeat Play B Repeat PlayRepeat Flashing a will become a flashing BForward and Reverse Searching SP/LP/SLP Playback OptionsSuper High Speed Searching LP/SLP Viewing a Still PictureGround Blue BackgroundTo block ratings, follow the steps below SmartLockSmartLock cont’d Ratings are defined onExample Specific Sub-ratings After you enter the code, the Smartlock menu will appear To change the access code, follow these stepsTo check the SmartLock settings, follow these steps Blocked RatingsTV-Y7 TV-G Sleep Timer Timer during a recordingPress the Combi button, then press the SLEEP/WAKE UP button Timer Sleep Wake UP Timer Sleep Wake UP TV on ON-TIMEExample Closed CaptionMenu ScreenClosed Caption cont’d Standard Closed CaptionsHalf-screen text Volume Bar Automatic Operation Features Smart Picture TV ResetPress the Mute button, then press the PAUSE/STILL button If another remote control beepsReminder Brightness Picture Color Tint Sharpness ReminderIndex Search Enter Index Number Tape in the TV/VCRSpecifications Glossary Helpful Hints Helpful Hints cont’d Limited Warranty Please contact Philips at French Speaking English SpeakingModel # Serial # Index Supplied Accessories