Philips CCA134AT Putting Batteries in the Remote Control, Erasure Prevention, TV/VCR Maintenance

Page 5

Before Using the TV/VCR 5

Putting Batteries in the Remote Control

1

Remove the battery compartment lid on the bottom of the remote control by pressing in the tab, then pulling up the lid.

2

Place three AA batteries inside the battery compartment with their + and – ends aligned as indicated.

3

Replace the battery compartment lid.

Erasure Prevention

Video cassette tapes have record tabs to ensure that recordings are not accidentally erased.

1

To prevent accidental erasure, break off the tab with a screwdriver.

2

To record again, cover the hole with cellophane tape.

Using the Remote Control

●Point the remote control at the TV/VCR’s remote sensor, then press the COMBI button when using the remote control to operate the TV/VCR. Point the remote control at the Cable Box/DBS, then press the CABLE/DBS button when using the remote control to operate the Cable Box/DBS.

●Do not put objects between the remote control and the TV/VCR.

1

2

3

1

2

TV/VCR Maintenance

●In this TV/VCR, use only tapes with the mark. The use of other tapes may result in poor picture quality and excessive deposits on the video heads, which may not be covered by the warranty if damage occurs.

●Make sure any light adhesive stick-on notes are removed from the video cassette tape before putting the tape in the TV/VCR. Removable labels like these can jam the TV/VCR.

●Periodic maintenance is required to maintain your TV/VCR’s excel- lent performance. This TV/VCR has an automatic head cleaning system. However, the video heads will eventually require cleaning or replacement. Only an authorized service center should perform this service.

Helpful Hints

•The remote control and its batteries are supplied.

•Do not mix alkaline and man- ganese batteries.

•Do not mix old and new batteries.

Image 5

Contents CCA134AT For Customer Use Dear Philips Magnavox product ownerModel No Serial No RA T I OIntroduction FeaturesSafety Precautions Table of Contents Using the Remote Control Putting Batteries in the Remote ControlTV/VCR Maintenance Erasure PreventionHooking Up the TV/VCR Hook up your TV/VCR using one of the connections shownRF coaxial cable Not supplied Rod AntennaBent pin Hooking Up the TV/VCR cont’dCrooked Pin Straight Pin Cable PlugPress the Menu button. The screen shown below will appear Turning On the TV/VCRSelect Language English Español Select KL or Press Menu to ContinueVCR Program VCR Setup Caption Reminder PRIM. SetupLanguage Selection Press the Combi button, then press the Menu buttonPress B Automatic Channel SetupPress the PLAY/o button or the STOP/p button to select Adding/Deleting ChannelsRepeat steps 3-4 to add or delete other channels Programming of the channel you added or deleted will appearCable Box users must set the clock manually Setting the ClockManual Clock Setting Month To Correct Press Clear To END Press Exit SET Manual Clock TimeDate To Correct Press Clear To END Press ExitAutomatic PBS Channel Selection Setting the Clock cont’dTime Wait for the TV/VCR to findSET Auto Clock Time NOW SearchingManual PBS Channel Selection NOW Searching flashes on the TV/VCR screen Use the Number buttons to select your PBS stationWait for the TV/VCR to find the time Auto Clock PBS CH Time Date NOW Searching To END Press ExitTime Daylight Savings Time Primary SetupDaylight-Savings Time Press the PLAY/ button or the STOP/ button to select PRIM. SETUP. Then, press the F.FWD/B buttonTime Zone Cable BOX Codes Setting the Remote to Operate a Cable Box/DBSSetting the Remote to Operate a Cable Box/DBS cont’d Front Panel Rear Panel AC Power CordANTenna Jack Connect your antenna or cable here. Details are on page sixRemote Control Buttons PAUSE/STILL Button VOLume m/n ButtonMemory Button REWind/ ButtonAdjust the picture control. Refer to the chart on Adjusting the Picture ControlsWhen you finish, press the STATUS/EXIT button Press the REWind/ button or the F.FWD/B button toDecrease Increase Adjusting the Picture Controls cont’dMore brilliant SofterIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status OFFInsert a tape in the TV/VCR PlayingPress the RECord/OTR button once to start recording Power button to turn on the TV/VCR, if necessaryRecording OTR Length Press OTR Cancel Press ClearOTR Different brands of equipment may operate differently Rerecording Tape DuplicationVCR Setup ONE Time Play Repeat Play ON-SCREEN Mode VCR Program VCR Setup CaptionDefeat Recording Follow the steps below to prevent accidental recordingSelect Program Number To END Press Exit Timer RecordingDaily Time OFF To Correct Press Clear To END Press Exit ONE Time Program Channel Time onTimer Recording cont’d Checking or Clearing Timer Recordings Station Setting Up the VCR Plus+ Programming SystemTV Channels VCR PLUS+ Cross REF. MAP Examine the lists onTo Select CH Press then Enter CH NO. to END Press Exit VCR PLUS+ Cross REF. MAP VCR PLUS+ CABLE/TVTo SET Press VCR + To Correct Press Clear To END Press Exit You have completed the steps on pagesVCR PLUS+ Program Timer Recording With the VCR Plus+ Programming System cont’d Appear on the screen Real-Time Counter MemoryVCR Setup ONE Time Play VCR Program VCR SetupRepeat Play B Repeat PlayRepeat Flashing a will become a flashing BForward and Reverse Searching SP/LP/SLP Playback OptionsSuper High Speed Searching LP/SLP Viewing a Still PictureGround Blue BackgroundTo block ratings, follow the steps below SmartLockExample Specific Sub-ratings SmartLock cont’dRatings are defined on After you enter the code, the Smartlock menu will appear To change the access code, follow these stepsTV-Y7 TV-G To check the SmartLock settings, follow these stepsBlocked Ratings Press the Combi button, then press the SLEEP/WAKE UP button Sleep TimerTimer during a recording Timer Sleep Wake UP Timer Sleep Wake UP TV on ON-TIMEExample Closed CaptionMenu ScreenHalf-screen text Closed Caption cont’dStandard Closed Captions Volume Bar Automatic Operation Features Smart Picture TV ResetPress the Mute button, then press the PAUSE/STILL button If another remote control beepsReminder Brightness Picture Color Tint Sharpness ReminderIndex Search Enter Index Number Tape in the TV/VCRSpecifications Glossary Helpful Hints Helpful Hints cont’d Model # Serial # Limited WarrantyPlease contact Philips at French Speaking English Speaking Index Supplied Accessories