Philips CCA134AT owner manual To change the access code, follow these steps

Page 50

50 SmartLock (cont’d)

To change the access code, follow these steps.

1

Press the COMBI button, then press the MENU button.

> SMARTLOCK

 

PRESS B

 

REVIEW

 

 

 

EXIT

 

 

 

PRIM. SETUP

 

 

 

VCR PROGRAM

 

 

 

VCR SETUP

 

 

2,4

POWER

 

EJECT

SLEEP/WAKE UP

SPEED

MEMORY

REC/OTR

 

PAUSE/STILL

PLAY

REWF.FWD

2

Press the PLAY/button or the STOP/button to select SMARTLOCK. Then, press the F.FWD/B button.

SMARTLOCK

__ _ _

Enter Your Access Code

3

Use the Number buttons to enter your old access code. The default code is 0711. If you have never set up your personal access code, use 0711 now.

After you enter the code, the SMARTLOCK menu will appear.

1

STOP

MENU

 

STATUS/EXIT

 

 

 

1 2 3

4 5 6

7 8 9

A.CH 0

CABLE/DBS COMBI

 

VCR PLUS+

VAR.SLOW

/ENTER

TRACKING

F.ADV

SMART

SKIP INDEX

PICTURE

SEARCH SEARCH

CLEAR

CH.

VOL.

MUTE

SLOW

6

SMARTLOCK

X X X-

Enter Your Access Code

4

Press the PLAY/button or the STOP/button to select CHANGE CODE. Then, press the F.FWD/B button.

SMARTLOCK

BLOCK

>CHANGE CODE

SELECT KL CHOOSE B

TO END PRESS EXIT

5

Use the Number buttons to enter your desired access code in the New Code space. Then, enter the same code in the Confirm Code space.

Your new access code should be recorded. You will return to the SMARTLOCK menu.

New Code

 

_

_ _ _

 

 

 

 

 

 

Confirm Code

_

_ _ _

6

3,5

Helpful Hints

In order to protect the privacy of the access code, an X will appear on the screen instead of the num- ber you enter.

If a “Wrong Code...” message appears on the screen after you complete step 5, you entered the wrong numbers in the Confirm Code space. Repeat the steps on this page.

You cannot use the default code after you set up your personal access code.

If a power failure occurs, the default code, 0711, will be the active access code again.

If you connect the power cord to an AC outlet that is controlled by a wall switch, your personal access code will be erased every time you turn off the power at the wall switch. The default code will be the active code again.

Press the STATUS/EXIT button.

Image 50
Contents CCA134AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use RA T I OIntroduction FeaturesSafety Precautions Table of Contents TV/VCR Maintenance Putting Batteries in the Remote ControlUsing the Remote Control Erasure PreventionRF coaxial cable Not supplied Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR Rod AntennaCrooked Pin Straight Pin Hooking Up the TV/VCR cont’dBent pin Cable PlugSelect Language English Turning On the TV/VCRPress the Menu button. The screen shown below will appear Español Select KL or Press Menu to ContinueLanguage Selection PRIM. SetupVCR Program VCR Setup Caption Reminder Press the Combi button, then press the Menu buttonAutomatic Channel Setup Press BRepeat steps 3-4 to add or delete other channels Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Programming of the channel you added or deleted will appearCable Box users must set the clock manually Setting the ClockManual Clock Setting Date SET Manual Clock TimeMonth To Correct Press Clear To END Press Exit To Correct Press Clear To END Press ExitSetting the Clock cont’d Automatic PBS Channel SelectionSET Auto Clock Time Wait for the TV/VCR to findTime NOW SearchingManual PBS Channel Selection Wait for the TV/VCR to find the time Use the Number buttons to select your PBS stationNOW Searching flashes on the TV/VCR screen Auto Clock PBS CH Time Date NOW Searching To END Press ExitTime Daylight Savings Time Primary SetupDaylight-Savings Time Press the PLAY/ button or the STOP/ button to select PRIM. SETUP. Then, press the F.FWD/B buttonTime Zone Setting the Remote to Operate a Cable Box/DBS Cable BOX CodesSetting the Remote to Operate a Cable Box/DBS cont’d Front Panel ANTenna Jack AC Power CordRear Panel Connect your antenna or cable here. Details are on page sixRemote Control Buttons Memory Button VOLume m/n ButtonPAUSE/STILL Button REWind/ ButtonWhen you finish, press the STATUS/EXIT button Adjusting the Picture ControlsAdjust the picture control. Refer to the chart on Press the REWind/ button or the F.FWD/B button toMore brilliant Adjusting the Picture Controls cont’dDecrease Increase SofterIf you select Status ON, then select Counter only on On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status OFFPlaying Insert a tape in the TV/VCRPress the RECord/OTR button once to start recording Power button to turn on the TV/VCR, if necessaryRecording OTR Length Press OTR Cancel Press ClearOTR Rerecording Tape Duplication Different brands of equipment may operate differentlyDefeat Recording VCR Program VCR Setup CaptionVCR Setup ONE Time Play Repeat Play ON-SCREEN Mode Follow the steps below to prevent accidental recordingSelect Program Number To END Press Exit Timer RecordingDaily ONE Time Program Channel Time on Time OFF To Correct Press Clear To END Press ExitTimer Recording cont’d Checking or Clearing Timer Recordings Station Setting Up the VCR Plus+ Programming SystemTV Channels To Select CH Press then Enter CH NO. to END Press Exit Examine the lists onVCR PLUS+ Cross REF. MAP VCR PLUS+ Cross REF. MAP VCR PLUS+ CABLE/TVTo SET Press VCR + To Correct Press Clear To END Press Exit You have completed the steps on pagesVCR PLUS+ Program Timer Recording With the VCR Plus+ Programming System cont’d Real-Time Counter Memory Appear on the screenVCR Program VCR Setup VCR Setup ONE Time PlayB Repeat Play Repeat PlayFlashing a will become a flashing B RepeatSuper High Speed Searching LP/SLP Playback OptionsForward and Reverse Searching SP/LP/SLP Viewing a Still PictureBlue Background GroundSmartLock To block ratings, follow the steps belowExample Specific Sub-ratings SmartLock cont’dRatings are defined on To change the access code, follow these steps After you enter the code, the Smartlock menu will appearTV-Y7 TV-G To check the SmartLock settings, follow these stepsBlocked Ratings Press the Combi button, then press the SLEEP/WAKE UP button Sleep TimerTimer during a recording Timer Sleep Wake UP TV on ON-TIME Timer Sleep Wake UPMenu Closed CaptionExample ScreenHalf-screen text Closed Caption cont’dStandard Closed Captions Volume Bar Automatic Operation Features TV Reset Smart PictureIf another remote control beeps Press the Mute button, then press the PAUSE/STILL buttonReminder Reminder Brightness Picture Color Tint SharpnessTape in the TV/VCR Index Search Enter Index NumberSpecifications Glossary Helpful Hints Helpful Hints cont’d Model # Serial # Limited WarrantyPlease contact Philips at French Speaking English Speaking Index Supplied Accessories