Philips CCA134AT Hooking Up the TV/VCR, Hook up your TV/VCR using one of the connections shown

Page 6

6 Hooking Up the TV/VCR

1

Hook up your TV/VCR using one of the connections shown.

A.

Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna

Connect a Cable signal or an antenna to the ANT(enna) Jack.

ANT.

B.

Connect the Cable signal to the IN Jack on the Cable Box.

Hooking Up Your TV/VCR With a Cable Box

To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box.

Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR.

OUTIN

RF coaxial cable

(not supplied)

ANT.

C.

Hooking Up Your TV/VCR With an Indoor Antenna

To install a rod antenna (not sup- plied), push the stem of the antenna into the antenna hole on the top of the TV/VCR. Connect the antenna wire to the ANT(enna) Jack on the back of the TV/VCR as shown. Extend the antenna and adjust its length, direction, and angle for the clearest picture.

Rod Antenna

(not supplied)

ANT.

Image 6
Contents CCA134AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use RA T I OFeatures Safety PrecautionsIntroduction Table of Contents TV/VCR Maintenance Putting Batteries in the Remote ControlUsing the Remote Control Erasure PreventionRF coaxial cable Not supplied Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR Rod AntennaCrooked Pin Straight Pin Hooking Up the TV/VCR cont’dBent pin Cable PlugSelect Language English Turning On the TV/VCRPress the Menu button. The screen shown below will appear Español Select KL or Press Menu to ContinueLanguage Selection PRIM. SetupVCR Program VCR Setup Caption Reminder Press the Combi button, then press the Menu buttonAutomatic Channel Setup Press BRepeat steps 3-4 to add or delete other channels Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Programming of the channel you added or deleted will appearSetting the Clock Manual Clock SettingCable Box users must set the clock manually Date SET Manual Clock TimeMonth To Correct Press Clear To END Press Exit To Correct Press Clear To END Press ExitSetting the Clock cont’d Automatic PBS Channel SelectionSET Auto Clock Time Wait for the TV/VCR to findTime NOW SearchingManual PBS Channel Selection Wait for the TV/VCR to find the time Use the Number buttons to select your PBS stationNOW Searching flashes on the TV/VCR screen Auto Clock PBS CH Time Date NOW Searching To END Press ExitPrimary Setup Daylight-Savings TimeTime Daylight Savings Time PRIM. SETUP. Then, press the F.FWD/B button Time ZonePress the PLAY/ button or the STOP/ button to select Setting the Remote to Operate a Cable Box/DBS Cable BOX CodesSetting the Remote to Operate a Cable Box/DBS cont’d Front Panel ANTenna Jack AC Power CordRear Panel Connect your antenna or cable here. Details are on page sixRemote Control Buttons Memory Button VOLume m/n ButtonPAUSE/STILL Button REWind/ ButtonWhen you finish, press the STATUS/EXIT button Adjusting the Picture ControlsAdjust the picture control. Refer to the chart on Press the REWind/ button or the F.FWD/B button toMore brilliant Adjusting the Picture Controls cont’dDecrease Increase SofterIf you select Status ON, then select Counter only on On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status OFFPlaying Insert a tape in the TV/VCRPower button to turn on the TV/VCR, if necessary RecordingPress the RECord/OTR button once to start recording Length Press OTR Cancel Press Clear OTROTR Rerecording Tape Duplication Different brands of equipment may operate differentlyDefeat Recording VCR Program VCR Setup CaptionVCR Setup ONE Time Play Repeat Play ON-SCREEN Mode Follow the steps below to prevent accidental recordingTimer Recording DailySelect Program Number To END Press Exit ONE Time Program Channel Time on Time OFF To Correct Press Clear To END Press ExitTimer Recording cont’d Checking or Clearing Timer Recordings Setting Up the VCR Plus+ Programming System TV ChannelsStation To Select CH Press then Enter CH NO. to END Press Exit Examine the lists onVCR PLUS+ Cross REF. MAP VCR PLUS+ Cross REF. MAP VCR PLUS+ CABLE/TVYou have completed the steps on pages VCR PLUS+ ProgramTo SET Press VCR + To Correct Press Clear To END Press Exit Timer Recording With the VCR Plus+ Programming System cont’d Real-Time Counter Memory Appear on the screenVCR Program VCR Setup VCR Setup ONE Time PlayB Repeat Play Repeat PlayFlashing a will become a flashing B RepeatSuper High Speed Searching LP/SLP Playback OptionsForward and Reverse Searching SP/LP/SLP Viewing a Still PictureBlue Background GroundSmartLock To block ratings, follow the steps belowSmartLock cont’d Ratings are defined onExample Specific Sub-ratings To change the access code, follow these steps After you enter the code, the Smartlock menu will appearTo check the SmartLock settings, follow these steps Blocked RatingsTV-Y7 TV-G Sleep Timer Timer during a recordingPress the Combi button, then press the SLEEP/WAKE UP button Timer Sleep Wake UP TV on ON-TIME Timer Sleep Wake UPMenu Closed CaptionExample ScreenClosed Caption cont’d Standard Closed CaptionsHalf-screen text Volume Bar Automatic Operation Features TV Reset Smart PictureIf another remote control beeps Press the Mute button, then press the PAUSE/STILL buttonReminder Reminder Brightness Picture Color Tint SharpnessTape in the TV/VCR Index Search Enter Index NumberSpecifications Glossary Helpful Hints Helpful Hints cont’d Limited Warranty Please contact Philips at French Speaking English SpeakingModel # Serial # Index Supplied Accessories