Philips PFL50X8K/12, PFL50X8T/12 Channels, Reset picture and sound, Automatic installation

Page 37

Reset picture and sound

You can restore the default picture and sound settings, while the channel installation settings remain the same.

1.While you watch TV, press .

2.Select [Setup] > [TV settings] > [General

settings] > [Factory settings], then press OK.

3. Select [Reset], then press OK.

All TV settings (except for channel settings) are reset to the default factory settings.

Channels

Automatic installation

When the TV was switched on for the first time, a full installation of channels was performed.

To change your language, country and reinstall all available TV channels, you can run this full installation again.

Start installation

Note: If you are prompted to enter a code, enter '8888'.

1.Press .

2.Select [Setup] > [Search for channels] >

[Reinstall channels], then press OK.

3.Select your country, then press OK.

4.Select your network, then press OK:

∙[Antenna (DVB-T)]: Access free-to-air antenna transmissions.

∙[Cable (DVB-C)]: Access cable transmissions.

5.Follow the onscreen instructions to select other options, if any.

The start menu for channel search is displayed.

6.Select [Start], then press OK.

7.Once the channel search is complete, select [Finish], then press OK.

Tip: Press LIST to see the channel list.

Note: When digital TV channels are found, the list of installed channels may display empty channel numbers. You can rename or reorder these channels.

Install analogue channels

 

 

You can search and store analogue TV

English

channels one by one.

 

Step 1: Select your system

 

Note: Skip this step if your system settings

 

are correct.

 

1. While you watch TV, press .

2.Select [Setup] > [Channel settings] > [Channel installation].

3.Select [Analogue: Manual installation] > [System], then press OK.

4.Select the system for your country or region, then press OK.

Step 2: Search and store new TV channels

1. While you watch TV, press .

2.Select [Setup] > [Channel settings] > [Channel installation].

3.Select [Analogue: Manual installation] > [Search channel], then press OK.

4.Find the channel:

∙If you know the channel frequency, enter it with the Navigation buttons or Numeric buttons.

∙If you do not know the channel frequency, search for the next

frequency that has a strong signal. Select [Search], then press OK.

5.After you have found the correct channel, select [Done], then press OK.

6.Select [Store as new channel], then press OK to store the new TV channel.

Note: If the reception is poor, reposition your antenna and repeat the procedure.

Install digital channels

If you know the channel frequency of the channels you want to install, you can search and store digital channels one by one. For best results, contact the service provider.

1.Press .

2.Select [Setup] > [Channel settings] >

[Channel installation].

EN 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents PFL50x8H/12 PFL50x8K/12 PFL50x8T/12 PFL50x8T/60 PFL50x8M/08 Contents Precautions SafetyRisk of electric shock or fire 3D health warning CareScreen Legal Placement tips3D glasses Lock the TVOpen source Pixel characteristicsCE compliance Compliance with EMFTrademarks and copyrights SustainabilityEnergy efficiency This TV is designed with energy-efficientRecycling Help and support Remote control Sensors and indicatorsTV controls Rear controlsEasyLink controls On-screen remote controlSmartphone control Adjust TV volume Switch TV on or offSwitch the TV on Watch TVManage favourite channels Switch TV channelsManage channel lists Filter channelsDevices Change device settings Use picture and sound presetsWatch connected devices Select the channel to lock, then pressChange picture format View programme guideWhat you can do From the broadcasterWhat you need Watch 3DStart 3D Switch on lounge light Switch onTo switch Ambilight on or off, select On or Off AmbilightSet up media sharing Change settingsPlay multimedia files Play files from computerPlay options Play files from USB devicePlay DivX VOD Video On Demand Smart TV∙ To stop the music, press Music options ∙ Repeat Select Repeat to play aNew Access Smart TV appsSmart TV options Interactive TVRent online videos You can identify channels that offer Access interactive TVPause TV Install USB hard drive∙ You can pause a programme for a maximum of 90 minutes Pause a live TV broadcast Record TV shows∙ Tune your TV to receive digital TV Schedule recordings Start recordingOne-touch recording View programme informationWatch recordings Use SkypeDelete recordings Manage contacts Start SkypeOnline status Make voice and video callsMake a voice call Select the contact, then press OKManage voicemails Skype settingsView Text Play gamesSet locks and timers You can switch the TV to standby after a Sleep timerChild lock Parental rating More picture settings Settings assistantBrilliant, high-definition image Advanced sharpness Enable Picture and soundAudio format More sound settingsAutomatic installation Reset picture and soundInstall analogue channels Install digital channelsAutomatic update Update channel listFine-tune analogue channels Copy channelsInstall satellite channels Satellite settingsAdd and remove satellites Language settingsMenu language Audio languageUniversal access settings Update software Other settingsHome mode TV demoUpdate from digital broadcast Update with USB∙ If a power failure occurs during UpgradeUpdate from the Internet Reset allYou can also update the TV software Cable quality About cablesPb Pr Connect devices Connect antennaBlu-ray or DVD disc player Connect the antenna to the TVTV receiver Connect the digital TV receiver to the TV with a Scart cable Video recorderConnect the recorder to the TV with a Scart cable Game consoleConnect the game console to the TV with an Hdmi cable Home theatre Connect the digital camera to the TV with a USB cable Digital cameraDigital camcorder USB storage device Connect more devicesComputer Connect the computer to the TV with an Hdmi cableVideo call camera ∙ If you need extra USB connectors, use a USB hubKeyboard and mouse If you add or remove a device, update the source list Update the source listWatch connected devices Select a deviceChange device settings Set up EasyLink devicesChange the device type One-touch playSelect speaker output Control devicesRetain picture quality Connect to a network and the InternetMaximise video display ConnectWiFi integrated Wired connectionNetwork settings Connect a CAM Conditional Access ModuleSwitch on Miracast Clear Wi-Fi Miracast devices Switch on remote recordingPush the CAM in as far as it will go Access CAM servicesChannel issues General issuesYou want to install TV channels Installing analogue or digital channels. If youSound issues Picture issuesNetwork issues Connection issuesThere are problems with Hdmi devices USB device content is not displayedAre printed on the back of the TV and on Contact PhilipsPackaging Display resolutions Power and receptionDisplay and sound MultimediaJpeg *.jpg, *.jpeg, *.mpo Supported audio/video formats Supported audio formats Connectivity ∙ USB 1 ∙ Headphones Stereo 3.5 mm mini-jackHelp version UMv 500812125003Index 3D, switch off AmbilightLounge light Network, TV name Universal access, enable From Koninklijke Philips Electronics N.V
Top Page Image Contents