Philips FTR 9965/12 manual Before calling Service

Page 44

Before calling Service

Ambient temperature

Do not hang up the monitor above a central heating or other heating sources. If the power/standby indicator in front is red and blinking, the temperature inside the monitor has become too high and has activated the protector.The monitor will be turned off. Unplug the power cord and wait for the monitor to cool down.

Care of the screen

Clean the anti-reflex coated flat glass screen with a slightly damp soft cloth. Do not use abrasives solvents as it can damage the glass surface of the screen.

Plasma Display characteristics

Caution:A video source (such as a video game, DVD, or video information channel) which shows a constant non-moving pattern on the monitor, can cause damage to the screen.When your Flat-Monitor is continuously used with such a source, the pattern of the non-moving portion of the game (DVD, etc.) could leave an image permanently on the screen.When not in use, turn the video source OFF.

To prevent or to reduce burn-in of the screen, select a LONG LIFE setting in the OPTIONS1 menu. See p. 8.

Very incidentally and after a longer period of unuse (approx. 1 year) the screen may display some strange colour deficiencies. This is quite normal for plasma displays and these effects will disappear after the set has been turned on for some time.

A plasma display consists of more than 1,2 Million colour pixels. It is within industry standards that very few pixels (< 0.001%) may be defective, even for a new set. There is however no reason to doubt about the quality of the set.

The plasma display technology operates with rare gases which are being influenced by air pressure. Up to an altitude of 2000m above sea-level (local air pressure equal or above 800 hPa), the display is functioning fine. Operating the set at a higher altitude (lower air pressure), the picture becomes unstable and the picture performance is deteriorating.

The plasma display might then also produce a humming sound. After bringing the set below 2000 m (local air pressure equal or above 800 hPa) it works fine again.Transportation has no influence.

Control of peripheral equipment

The infrared radiation of the screen may influence the reception sensitivity of other peripherals. Solution: replace the batteries of the remote control or change position of other equipment. E.g. keep away a wireless headphone from within a radius of 1,5 m.

No stable or not synchronised VGA picture

Check if you have selected the correct display mode in your PC. See Table of Signal Supported.

No picture

Are the supplied cables connected properly? (The power cable to the display, the VGA cables,...)

Is your PC switched on?

Do you see a black screen and the indicator in front of the monitor lights up green, this means that the display mode is not supported.

Switch your VGA source to a correct mode.

Remote control

If your monitor no longer responds to the remote control, the batteries may be exhausted.

If your problem is not solved: Switch your monitor off and then on again.

Never attempt to repair a defective monitor yourself.

Check with your dealer or call a video technician.

Transport

Keep the original packaging to transport the monitor if needed.

End of life directives

Philips is paying a lot of attention to produce environmentally-friendly in green focal areas.Your new monitor contains materials which can be recycled and reused.

At the end of its life specialised companies can dismantle the discarded monitor to concentrate the reusable materials and to minimise the amount of materials to be disposed of.

Please ensure you dispose of your old monitor according to local regulations.

How to dispose of batteries ?

The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless in many countries batteries may not be disposed of with your household waste. Please ensure you dispose of batteries according to local regulations.

Miscellaneous

. Ambient temperature: + 5~ + 40°C

. Maximum operating altitude: 2000 m/6526 ft

(min. air pressure 800hPa)

. Mains:AC 100-240V

. Standby consumption: 1 W

. Weight (excl. packaging) Display: 46 kg

. Dimensions (wxhxd):

Display: 124,2 x 76,7 x 11 inch

. Wall mounting bracket included

Settings are out of adjustment

Select RESET in the OPTIONS 1 menu, p. 8 to restore the predefined factory settings.

12Before calling Service

Image 44
Contents Flatl TV Cable Installation AnvändningAnslutning av extrautrustning Modell FTR 9965/12 Produkt No AGFörberedelser TV-mottagarenhet + monitor utan högtalareBetjäning av fjärrkontrollen RC4301 Tangenterna på mottagarens framsida BildformatGå till Gå ur och tryck på MENU-knappen Active control se sInstallation Installationsmenyn innehåller följande punkterVälj språkmeny och land Användning av menyernaAutomatisk installation Manuell installationLagra TV-stationer OBS! Sökning eller direktval av TV-kanalNamnge Arbeta om programöversiktenVälj favoritprogram OBS! Det går inte att ändra namn på VGA-källanUppsättning AllmäntKälla TV meny BildmenyDekoder Active Control Ljud-menyn EgenskapermenyVälj textremsor Dubbla bilder / PIP / Multipip VisningsalternativScan PIP3, PIP8 eller PIP Bestäm position på den enskilda PIP bildenNextview / Text-TV guide Öppna NEXTVIEW/Text-TV guideBild/NEXTVIEW Text-TV guide Nextview guiderText-TV guide BasfunktionerInsamling och uppdatering av Nextview information Titta för att titta på valt program som sänds just dåText-TV Hur Text-TV kopplas till och frånAtt välja en Text-TV-sida Föregående text-TV-sidaText-TV meny VisaFavorit SökningAtt ansluta extrautrustning Videobandspelare VCR-DVD+RWDVD-spelare Dekoder och videobandspelareSidoanslutningar Mångkanal Surround mottagareCinema Link Surround förstärkare Att ansluta datorVGA meny Bandspelare och DVD som har EasyLinkVälj en av menyerna med markörknappen vänster/höger Bild Ljud UppsättnVCR timer Surround till/från AMP, CD Markörknapp upp/ner Audio- och videoapparater-knappenVälja dellägen för DVD+RW, SAT, CDR Inspelning med bandspelare som har EasyLinkTips Luft- och vattenföroreningar Elförbrukning 1 WMed TV-skärmen Tillämpliga. Hörlursanslutning undantagenPage RecorderDVD Konfiguration av Cinema Link-utrustningen Förberedelse och användningAv dessa RekommendationLjudmeny Starta CinemaLinkReceiver meny Högtalarmeny SurroundmenyAutomatisk installation Manuell installationNamnge Omfördelning MW, SW, FM eller AMInstallation Location Unpacking and wall mounting instructions Unpacking and wall mounting instructionsRemove the packaging Attach the display fittingsAssembling and mounting the wall mount unit Mounting the plasma displayRS 232c Serial I/O port Connect Peripheral EquipmentConnect Peripheral Equipment Connect your computer + Operation OperationUse of the remote control Use of the remote controlSignals Picture formatPicture menu Use of the menus and the menu systemUse of the menus and the menu system Screen settings menu Options 1 menuSelect Screen Wiper on or OFF Select Long Life‘ Select Inverse ON, OFF or WT Setting a computer image to the correct RGB select screen Setting high definition images to the suitable screen sizeSetting the picture size for RGB input signals Options 2 menuSupported resolution Table of Signals SupportedTable of Signals Supported Before calling Service Before calling Service
Related manuals
Manual 42 pages 14.22 Kb