Philips Flat TV manual Setting the remote control to work accessory devices, Code setup

Page 29

Setting the remote control to work accessory devices

Your remote control is set to work your TV and many infrared remote (IR) control VCRs, Cable TV Converter Boxes, DVD players, Satellite Receivers, etc.

Press the Select button repeatedly to select DVD/R, CBL, VCR or AUX according to the accessory device you want to operate with this remote control. See Use of the Remote control, p. 3. Press the POWER button.

If the function buttons on the remote control also work the selected accessory device, then the remote is ready and no further steps are needed.

If the function buttons do not work with the selected accessory device, according to the device(s) you own, you may make your remote control ready for them by a direct entry code. Proceed as following.

Code setup

&Press the Select and POWER buttons at the same time, then release.

éNOTE:When inputting the digits as described below, you must not allow more than 20 seconds to pass between the input of each digit or you will need to return to step 1 and begin the programming process again.

Input the appropriate digit provided below for the type of accessory device you want to operate:

1 DVD/R

2 CBL (HD-STB)

3 CBL-SAT

4 VCR

5 AUX (AMP, CD).

“Input the 4-digit code for the type and brand of accessory device. The codes are listed on pages 25-26.

‘The green light behind the POWER button will blink for 3 seconds to show that a valid code was input.

If a valid code was not entered, the light will stay on continuously for 3 seconds. If that occurs, go back to step 1 and begin the programming process again.

(Now you will try to use the TV remote with the accessory device. Press the Select button on the remote to cycle across the accessory mode dial. Stop pressing the button when the mode you desire is lighted. The light will stay on for 2 seconds and then begin blinking. The blinking means that the remote is in the accessory mode you have selected.

§Within 60 seconds from the time the blinking starts, point the remote toward the accessory device and press the POWER button. If the device does not respond to the POWER command, follow the steps for programming the remote again using a different setup code for the type and brand of accessory device you wish to operate. Refer again to the code list on pages 26-27. If no more codes are listed for the type and brand of accessory device, the remote likely will not operate your particular model of accessory device.

Notes:

-Your TV remote is not necessarily capable of being programmed to operate all models of the brands of accessory devices listed on pages 26-27.You may want to try the programming process again. Try using the number(s) that are listed for your type and brand of device to be sure you did not make a mistake in inputting the digits during your first attempt at programming.

-If the remote control is in one of the accessory modes (a mode light is flashing) — DVD/R, CBL, SAT, VCR or AUX — and you don’t press any of the remote buttons for sixty seconds, a “time-out” occurs, returning the remote to TV mode.

25

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Page Page Notification Proof of Purchase Product Safety Additional BenefitsDear Philips product owner Product OwnershipImportant Safety Instructions Contents Preparation Use of the remote control RC4307 Surf CH Channel selectionActive Control See p Buttons on top or on the right side of the TVInstallation menu contains the following items InstallationProceed with the Install menu To use the menusStore TV channels General Settings menuOSD On Screen Display Caption ServiceSet/Change PIN ImportantYou have forgotten your PINClock Auto clock modeAuto clock channel Time DayDemo Center input Center in volumeDigital processing, Light sensor and 3D Y/C Comb filter On Or OffPicture menu TV menuAuto picture Digital processingSound Active ControlAmbilight modes AmbilightSleep Timer Features menuSelect Sleep Timer with the cursor down On timer Closed CaptionsTV-Y TV-Y7 TV Ratings LockChannel remove Movie Ratings LockDisplay options Dual screen / PIP / MultipipScan PIP3 or PIP Define the position and the size of the single PIP screenRecorder VCR-DVD+RW Connect Accessory DevicesRecorder and other A/V devices If your recorder has an S-VHS video jackSatellite Receiver / Cable Box with AV outputs Recorder and Cable Box with outputRecorder and Satellite Receiver / Cable Box with AV outputs If your satellite receiver or cable box has an S-Video jackDevices with Component Video Output Connectors DVD Player or other accessory digital source devicesDevices with an S-Video connector YPbPrMulti channel Surround receiver Hdmi High Definition Multimedia Interface connector640/720 x 480p 720 x 576p 1280 x 720pSide connections Connect extra subwooferTo select connected devices Camera, Camcorder, GameRecord with your recorder Audio- and video equipment buttonsFor pause For record Record a TV programCode setup Setting the remote control to work accessory devicesRemote Control Direct Entry Codes for Accessory Devices VCR Regulatory Notices Federal Communications Commission NoticeCheck if you have selected the correct VGA mode in your PC Calling ServiceTo air and water pollution. Power consumption 2 W See Extras, Specifications on this CDTips Your warranty does not cover One Year Free Labor One Year Free Service on PartsProduct used for commercial or institutional purposes Please contact Philips at French speaking English speakingEn el Canadá CanadaAu Canada Philips Factory Dequindre Madison Heights, MI 48071 Philips Factory Service 1110 N. Post Oak Rd., Suite 100
Top Page Image Contents