Philips VRZ220AT, VRZ250AT owner manual Turning on Your VCR, 2Turn on the TV

Page 11

VRZ220/250 layout 4/8/99 10:11 PM Page 11

Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected correctly.

●You can not program channels if you are using a Cable Box or a Direct Broadcast System.

1

Press the POWER button. The VCR/TV light and the POWER light will appear on the display panel.

2

Turn on the TV. Set it to the same channel as the CH3/CH4 switch on the back of the VCR. The display shown below will appear. (If the display does not appear, check your hookups, then follow the steps on page 12 to set up channels and page 17 to select a language.)

SELECT op
→ ENGLISH	ON
ESPAÑOL

MAKE SELECTION OR

PUSH MENU TO CONTINUE

Turning on Your VCR 11

2Turn on the TV.

1	POWER		VCR/TV	EJECT
1	1	2	3		5
	4	5	6		5
	4	5	6
4	7	8	9	CHANNEL
	7	8	9
		0	+100
	SPEED	TIME SEARCH		MEMORY
	MENU	STATUS/EXIT	CLEAR	SLOW
3	REWIND	/PLAY		F.FWD
3	REC/OTR	/STOP		PAUSE/STILL

3

Within 60 seconds, press the PLAY/o button or the STOP/p button to select English or Spanish on-screen displays.

4

Press the MENU button. The display shown below will appear.

CONNECT ANTENNA OR CABLE

TO VCR

THEN . . .

PUSH CH UP KEY

OR . . .

FOR PLAY ONLY – PUSH STOP

5

Within 60 seconds, press the CHANNEL o button to begin automatic channel programming. AUTO SET PRO- CEEDING PLEASE WAIT will appear on-screen. The VCR will memorize all available channels. When all channels are pro- grammed, CHANNELS ARE SET will appear on-screen briefly, then TV programming will appear.

Now, when you press the CHANNEL o/p buttons, you’ll only scan through channels that you receive.

Helpful Hints

•To skip this feature and play a tape immediately, insert a tape with its record tab removed. Or, to skip step 3, press the MENU button. All on- screen displays will be in English. To skip step 5, press the STOP/p but- ton. Channels will not be pro- grammed, and CHANNELS NOT SET will appear on-screen.

•If you try to program channels when there is no antenna or cable connected to the VCR, programming will appear to take place, but even- tually a NO TV SIGNALS message will appear. Connect an antenna or cable to the VCR’s ANT(enna) IN Jack and try again. You may need to follow the steps on page 12.

•The TIMER light on the VCR will blink when the power is restored after a power failure of more than one minute.

Image 11

Contents VRZ220AT VRZ250AT For Customer Use Dear Philips Magnavox product ownerIntroduction FeaturesTable of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemCH3 Plug in the TV and the VCRRecording/Viewing Any Channel Hookups With a Cable Box / Direct Broadcast SystemConnections RF coaxial Cable TV’s Antenna Jack Recording One Channel/Watching AnotherCable Box/DBS VRZ220 Hookups With a Stereo TVVRZ250 Press the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsYou make each entry within 60 seconds of the previous entry Follow the steps below to set your VCR’s clock. Make sureDaylight-Saving Time Language Selection Menu Button Remote Control ButtonsPower Button Time Search Button VRZ250 onlyClear Button Remote Control Buttons cont’dEject Button Press to eject the tapeIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR RecordingPress the VCR/TV button to put the VCR in VCR posi Remote control to select channel 03 or 04 at the TVRecording One Channel/Watching Another To return to the channel being recorded, use the TVOne-Touch Recording Set up the channels at the VCRDaily Timer RecordingSlots will flash on-screen Timer Recording cont’dStandard Play Press the STATUS/EXIT button. Program WAS COMTape Speeds Tape Speed Maximum Record/Playback Time Type T160 T120 T60Program REVIEW, then press the F.FWD/B button Checking or Cancelling Timer RecordingsPress the PLAY/o button or the STOP/p button to select PROGRAM, then press the F.FWD/B buttonTurn on the TV and set it to channel 03 or 04, whichever Channel the CH3/CH4 switch on VCR 2 is set toRerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat PlayPress the Time Search button Time Search VRZ250 onlyReal-Time Counter Memory Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Or Receiver Understanding On-Screen DisplaysMono MonitorMulti-Channel Television Sound System VRZ250 only cont’d Please see additional notes on Hi-Fi Stereo Sound System VRZ250 onlyHi-Fi Stereo Sound System VRZ250 only cont’d Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Model # Serial # Limited WarrantyIndex Supplied Accessories